Abstract:A Ni/scandia-stabilized zirconia (ScSZ) cermet anode was modified by coating with nano-sized gadolinium-doped ceria (GDC, Gd0.2Ce0.8O2) prepared using a simple combustion process within the pores of the anode for a solid oxide fuel cell (SOFC) running on methane fuel. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed in the anode characterizations. Then, the short-term stability for the cells with the Ni/ScSZ and 2.0wt.%GDC-coated Ni/ScSZ anodes in 97%CH4/3%H2O at 700°C was checked over a relative long period of operation. Open circuit voltages (OCVs) increased from 1.098 to 1.179V, and power densities increased from 224 to 848mWcm−2, as the operating temperature of an SOFC with 2.0wt.%GDC-coated Ni/ScSZ anode was increased from 700 to 850°C in humidified methane. The coating of nano-sized Gd0.2Ce0.8O2 particle within the pores of the porous Ni/ScSZ anode significantly improved the performance of anode supported cells. Electrochemical impedance spectra (EIS) illustrated that the cell with Ni/ScSZ anode exhibited far greater impedances than the cell with 2.0wt.%GDC-coated Ni/ScSZ anode. Introduction of nano-sized GDC particles into the pores of porous Ni/ScSZ anode will result in a substantial increase in the ionic conductivity of the anode and increase the triple phase boundary region expanding the number of sites available for electrochemical activity. No significant degradation in performance has been observed after 84h of cell testing when 2.0wt.%GDC-coated Ni/ScSZ anode was exposed to 97%CH4/3%H2O at 700°C. Very little carbon was detected on the anodes, suggesting that carbon deposition was limited during cell operation. Consequently, the GDC coating on the pores of anode made it possible to have good stability for long-term operation due to low carbon deposition.

Influence of Characteristics of Stabilized Zirconia Electrolyte on Performance of Cermet Supported Tubular SOFCs

YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

Conductivity Of Yttria-Doped Ceria Electrolyte Made By Chemical Coprecipitation And Its Evaluation For Sofc Application

Fabrication and Performance of Anode-Supported Electrolyte Thin Films SOFCs

Tubular SOFC with Hollow Fiber Ceramic Support and Inner Coating

Al2O3 Toughening ScSZ Electrolyte Fabricated by Water-Based Tape Casting Technique for Solid Oxide Fuel Cells

Preparation of yttria-stabilized zirconia electrolyte via atmospheric plasma spraying for metal-supported solid oxide fuel cells

Production of Dense Yttria-Stabilized Zirconia Thin Films by Dip-Coating for IT-SOFC Application

Fabrication and Characterizations of Ysz Electrolyte Films for Sofc

Performance and Optimization of Ni/3 Mol% Y2O3-ZrO2 Anode Supported SOFC

Development of ScSZ Electrolyte by Very Low Pressure Plasma Spraying for High-Performance Metal-Supported SOFCs

High Performance Solid Oxide Fuel Cells Based on Tri-Layer Yttria-Stabilized Zirconia by Low Temperature Sintering Process

Impact of yttria-stabilized zirconia contents in nickel cermet anodes for intermediate temperature-operated syngas-fueled thin film solid oxide fuel cells

Development of yttria-stabilized zirconia thin films via slurry spin coating for intermediate-to-low temperature solid oxide fuel cells

Performance of Ni/Scsz Cermet Anode Modified by Coating with Gd0.2ce0.8o2 for an Sofc Running on Methane Fuel

Fabrication and Characterization of La0.6Sr0.4Co0.2Fe0.8O3-δ-Yttria Stabilized Zirconia Composites Cathode Prepared by Infiltration Method

Tape Casting of Bilayered Anode Supports and Electrochemical Performance of SOFCs Based on Them

Research on Sintering Process of YSZ Electrolyte

Nanocrystal Engineering of Thin-Film Yttria-Stabilized Zirconia Electrolytes for Low-Temperature Solid-Oxide Fuel Cells

Electrical properties of CeO2-Y2O3 electrolyte SOFCs