Abstract:The constraints of traditional manufacturing techniques have led to the generation of a considerable amount of waste superalloy, causing substantial resource wastage. The primary concern with waste superalloys lies in the excessive presence of inclusions and impurity elements, rendering them unsuitable for further utilization. This study proposes the use of directional solidification combined with electron beam melting and refining (EBMR) to prepare FGH4096 superalloy ingots (Φ120 mm), which offers a promising approach to produce large-sized powder superalloy master alloy ingots with high-purity and high homogeneity. It is found that the secondary dendrite arm spacing and the size of the γ' phase in the alloy are significantly reduced after EBMR treatment. The concentration of O and N can be decreased to 5.7 and 0.6 ppmw, respectively. The size of inclusion can be reduced below 8.69 μm and the inclusion numbers reduce by over 50 % compared with both conventional ingots. A droplet transfer mode and melt convection mode mechanism have been proposed, which accurately predicts the melting temperature and melt flow. A quantitative study is conducted on the influence of inclusion density, the contact angle between inclusions and melt, and the surface tension of the melt on capillary forces. The results indicate that the capillary forces between inclusions in the melt range from 1.8 × 10 −19 N and 1.9 × 10 −17 N. Furthermore, the collision-aggregation behavior of inclusions in the melt is discussed, and an estimate of the tendency of inclusion collision-aggregation is provided. The enrichment of inclusions in the EBMR ingot is primarily the result of turbulent collision. The Marangoni effect and the extremely high surface temperature of the melt promote the collision and agglomeration of inclusions, causing them to accumulate rapidly at the melt surface. Moreover, the thorough removal of inclusions through the decomposition and dissolution process of the electron beam offers theoretical backing for the preparation of superalloys through electron beam melting and high-purity refining.

Feasibility of Integrated Seed Making and Directional Solidification of Tial Alloy Using Cold Crucible

Production of Single-Crystal Seeds [001] from Nickel–Tungsten Alloys by Directional Crystallization

Temperature Field Evolution of Seeding during Directional Solidification of Single-Crystal Ni-Based Superalloy Castings

Research on directional solidification combined with electron beam melting and refining for recycling of FGH4096 alloy scraps

Phase-field Model Simulations of Alloy Directional Solidification and Seaweed-Like Microstructure Evolution Based on Adaptive Finite Element Method

Scalable manufacturing of the Al-based master composites containing TiB 2 and TiC particles and their modification effect on the hot cracking of rapidly solidified Al alloys

Substrate stimulating technique for Ni-based single crystal superalloy preparation during direction solidification

From research to cost-effective directional solidification and single-crystal production – an integrated approach

Preparation of Al-5.8%Cu Alloy Semi-Solid Slurry by Controlled Melting

Analysis of competitive growth mechanism of stray grains of single crystal superalloys during directional solidification process

Microstructure refinement and improvement of mechanical properties of Ti46Al8Nb0.9B alloys by electromagnetic cold crucible continuous solidification

Mixing process and nucleation of an Al-Si alloy during controlled diffusion solidification with simultaneous mixing and effect of mixing rate

Formation of Stray Grains During Directional Solidification of a Superalloy AM3

System design and hot zone optimization of monocrystalline silicon directional solidification furnace for PV application

Numerical Simulation And Optimization Of Directional Solidification Process Of Single Crystal Superalloy Casting

Microstructure Simulation to the Solidification Process of Single Crystal Guide Vane

Using the Phase Field Method to Investigate Microstructural Evolution of Semi-Solid 357.0 Slurries

Microstructural Investigations of Ni-Based Superalloys by Directional Solidification Quenching Technique

Modelling freckles and spurious grain formation in directionally solidified superalloy castings

Study on the Directional Solidification Process of an Aluminum Alloy Bar in Multishell Mold Being Gradually Immersed in Water

A new strategy to inhibit stray grain formation during laser directed solidification of single crystal superalloys