Abstract:For solid oxide fuel cells (SOFCs), metallic interconnects (ICs) are crucial components to add to the electrochemical catalyst electrodes. The high temperature operation condition in SOFCs is an extremely degrading factor for metallic ICs. Three metallic ICs have been selected in this thermal aging study. IC-1 and IC-2 contain similar Mn/Cr compositions. The thermal mechanical property of IC-2 is better than that of IC-1, attributed to the inclusion of rare earth elements. IC-3 has lower chromia composition, whereas IC-1 and IC-2 have higher Cr contents. Thermal aging is introduced under ambient atmosphere at 800°C from 0 to 100 h. X-ray diffraction study of the IC oxide scales shows growth of (MnCr)3O4 with the spinel structures. Scanning electron microscopy and energy dispersive spectroscopy (SEM/EDS) reveal the thickness and spinel particles for the three ICs, the oxide layers at about 0·9–1·3 μm thick and the spinel sizes at 1·0–1·3 μm. The oxide weight gain studies have shown that IC-3 is the more readily oxidised IC, with an estimated oxidation rate of ∼1·98×10−7 g2 cm−4 s−1 at 800°C. Thus, IC-3 should be better coated with a protective layer for SOFC applications. For the thermal Cr diffusion study, we applied homemade glass sealant on the surface of IC-1. After thermal aging for 1000 h under ambient atmosphere at 800°C, we examined the sample with micro-Raman. The cross-sectional microstructures were studied with SEM/EDS. Both Raman and SEM/EDS results indicated that the Cr ions penetrated into the glass sealant by ∼65 μm. The oxide scales on ICs are influential on the electrical conductivity. The electrochemical impedance spectroscopy study on IC-2 samples after thermal aging is also shown.

Oxidation of Haynes 230 alloy in reduced temperature solid oxide fuel cell environments

Oxidation behavior of a Ni-Fe support in SOFC anode atmosphere

Metallic interconnects for solid oxide fuel cell: Performance of reactive element oxide coating during long time exposure

Unravelling the oxidation behaviors of porous stainless steel 430L substrate for metal-supported solid oxide fuel cells

Metallic Interconnects for Solid Oxide Fuel Cell: Performance of Reactive Element Oxide Coating During 10, 20 and 30 Months Exposure

Cr-Based Alloy Used as Interconnect in Solid Oxide Fuel Cells

The effects of thermal aging on metallic interconnects of solid oxide fuel cells

Initial stage oxidation corrosion of commercial ferritic stainless steels with different Cr contents at 650 °C for solid oxide fuel cells

Oxidation behavior and interface diffusion of porous metal supported SOFCs with all plasma sprayed functional layers in air at 650oC

Effect of Temperature and Water Content on the Oxidation Behaviour and Cr Evaporation of High-Cr Alloys for SOFC Cathode Air Preheaters

Experimental Investigation of the Initial Stage of the Oxidation Mechanism of Co Coating for Solid Oxide Fuel Cell Interconnects at 650 °C

Metallic Interconnect Materials Used in Solid Oxide Fuel Cell

Development of Coating Materials on Alloy Interconnect in Solid Oxide Fuel Cell

High-Performance Low-Temperature Solid Oxide Fuel Cell with a Pt@C–Ni 0.8 Co 0.15 Al 0.05 LiO 2−δ Composite Cathode

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Properties of Fe–Cr Based Alloys As Interconnects in a Solid Oxide Fuel Cell

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Transparent conductive oxide type materials as the anode of solid oxide fuel cells at a reduced temperature

The effect of surface treatment on the oxidation of ferritic stainless steels used for solid oxide fuel cell interconnects

Degradation analysis of commercial interconnect materials for solid oxide fuel cells in stacks operated up to 18000 hours

Short-Term Oxidation Studies on Nicrofer-6025HT in Air at Elevated Temperatures for Advanced Coal Based Power Plants