Abstract:The impact strength of nylon 6 (polyamide 6) can be improved by blending impact strength modifier at ambient temperature and then the applications of nylon 6 can be expanded widely. Polyamide (6) PA 6/poly(ethylene-1-octene) elastomer (POE)/poly(ethylene-1-octene) elastomer grafted by maleic anhydride (POE-g-MA) ternary blends were prepared in corotating twin-screw extruder by two kinds of extrusion processes, more than 10-fold increase of impact strength at ambient temperature was obtained from impact test of specimens, not at much expense of tensile properties. The influence of extrusion process, that is, one- and two-step extrusion, on the micromorphology of toughing nylon 6 blends was investigated systematically. Scanning electron microscopy was used to observe the fracture surfaces of bars prepared by injection-molding machine. In addition to particle size and distribution, interparticle distance ( τ) between neighboring dispersed phase particles in PA6/POE-g-MA/POE ternary blends was calculated and used to characterize the micromorphology. Supertoughness was obtained in both ternary blends, and the interparticle distances ( τ) were 0.228 and 0.179 μm, respectively, which were less than the critical τ c (0.3 μm) in nylon/rubber blends. The results showed that more homogeneous distribution of POE phase in nylon 6 matrix was found in blends prepared by two-step extrusion method, in which the average particle size of POE phase was 0.313 μm, while the average particle size in blends prepared by one-step method was 0.399 μm. The half-peak width of Gaussian distribution curve of particle size in blends prepared by one-step extrusion method was 0.278, which is higher than that of blends prepared by two-step method with the value of 0.248.

A Novel Impact Modifier for Nylon 6

Radiation preparation of ultrafine carboxylated styrene-butadiene rubber powders and application for nylon 6 as an impact modifier

Preparation of a Structured Acrylic Impact Modifier and Its Application in Toughening Polyamide 6

STUDY ON NYLON 6／SUPERFINE RUBBER PARTICLES COMPOSITES VIA IN SITU POLYMERIZATION

Toughening of Polyamide‐6 with Little Loss in Modulus by Block Copolymer Containing Poly(styrene‐alt‐maleic Acid) Segment

Enhanced Mechanical Properties of Natural Rubber by Block Copolymer-Based Porous Carbon Fibers

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Toughening Of Polyamide-6 With A Maleic Anhydride Functionalized Acrylonitrile-Styrene-Butyl Acrylate Copolymer

Toughening of Nylon-6 with Epoxy-Functionalized Ethylene Propylene Rubber

Effects of Core-Shell Structured Rubber on Biobased Polyamide 56 with Stiffness and Toughness Balance

Toughening of nylon with epoxidised ethylene propylene diene rubber

Blends of Poly(2,6-Dimethyl-1,4-Phenylene Oxide)/Polyamide 6 Toughened by Maleated Polystyrene-Based Copolymers: Mechanical Properties, Morphology, and Rheology

The influence of extrusion process on micromorphology of PA 6/POE/POE-g-MA ternary blends: A quantitative analysis

Effects of Blending Time and Catalyst on the Properties of Nylon 1010/acrylate Rubber Blends

Toughening Mechanism of Long Chain Branched Polyamide 6

Short Nylon 6 Fibre Reinforced Polystyrene/Natural Rubber Blends: Effect of Maleated-Polystyrene Compatibiliser

Reactive Compatibilization and Elastomer Toughening of Poly(2,6-dimethyl-1,4-phenylene Oxide)/polyamide 6 Blends

Effect of poly(styrene-co-maleic anhydride) on physical properties and crystalline behavior of nylon-6/PEBA blends

Research on Compatibility and Surface of High Impact Bio-Based Polyamide