Abstract:Silica aerogels generally exhibit poor mechanical properties, which seriously restrict their commercial use and makes it necessary to reinforce their structures to obtain materials strong enough to withstand mechanical stresses. The incorporation of polymers into silica aerogels is a promising approach due to the enhancement in mechanical strength afforded and the possibility of imparting the hydrophobicity of the polymers to the resulting aerogels. However, the processes typically employed to prepare polymer-reinforced silica aerogels are complex, arduous and costly, requiring multiple washing and soaking steps for the infiltration of the polymer precursors after gelation and supercritical drying. Additionally, diffusion problems can result in heterogeneity in aerogel monoliths due to the use of various cross-linked polymers and the autoclave-limited dimensions of aerogels. In this study, a facile sol–gel route was developed to fabricate a large (500 cm3) polymer–silica aerogel monolith that was stable under atmospheric conditions and suitable for machining. The synthesis of the polymer–silica aerogels began with a facile one-pot reaction involving resorcinol (R), formaldehyde (F), methyltrimethoxysilane (MTMS), and N-(β-aminoethyl)-γ-aminopropyl-trimethoxysilane (AEAPTES), followed by an ambient-pressure drying process. The resulting aerogels were characterised by nitrogen adsorption–desorption, scanning electron microscopy (SEM), contact angle, and thermal conductivity measurements, and the aerogel mechanical properties were evaluated by a unidirectional compression test. The Young's modulus of compression of the aerogels was observed to increase from 3.95 to 34.88 MPa with an increase in the density of the aerogels from 0.14 to 0.26 g cm−3. Simultaneously, the aerogels were observed to be superhydrophobic, with a contact angle as high as 168°, and exhibited low thermal conductivity (0.038 W m−1 K−1) and good absorption for organic liquids, which are critical characteristics for the practical application of aerogels, especially in energy-saving and oil-/chemical-cleanup practices.

Synthesis of ultrahigh-pore-volume carbon aerogels through a “reinforced-concrete” modified sol–gel process

Preparation of Silica Aerogels Via Non-supercritical Drying and Their Formation Process

Synthesis and Structure of Carbon/Silica Hybrid Aerogels

Preparation of Silica Aerogels by Non-Supercritical Drying

Synthesis of Monolithic Carbon Aerogels with High Mechanical Strength Via Ambient Pressure Drying Without Solvent Exchange

Ambient-pressure drying synthesis of large resorcinol–formaldehyde-reinforced silica aerogels with enhanced mechanical strength and superhydrophobicity

Carbon Aerogel Films Synthesized at Ambient Conditions

Synthesis of Porous and Mechanically Compliant Carbon Aerogels Using Conductive and Structural Additives

Low-density, high-strength and large-scaled monolithic carbon aerogels fabricated via modified ambient pressure drying

Preparation and molding of ultralow-density silica aerogels

Synthesis of high specific surface area silica aerogel from rice husk ash via ambient pressure drying

Preparation of Monolithic Carbon Aerogels and Investigation of Their Pore Interconnectivity by a Nanocasting Pathway

Fabrication and Nano-Structure Control of Carbon Aerogels Via a Microemulsion-Templated Sol–gel Polymerization Method

On Porosity of Carbon Aerogels from Sol-Gel Polymerization of Phenolic Novolak and Furfural

Ultrahigh-strength silicone aerogels reinforced by an armor-like epoxy framework via a temperature-controlled sequential reaction strategy

Mechanical Properties of Novel Carbon Aerogels with Nanoscale Skeleton Derived from Resorcinol/Formaldehyde/Acetonitrile Sol-Gel System

The preparation of carbon aerogels based upon the gelation of resorcinol–furfural in isopropanol with organic base catalyst

One-pot Synthesis, Characterization and Properties of Acid-Catalyzed Resorcinol/formaldehyde Cross-Linked Silica Aerogels and Their Conversion to Hierarchical Porous Carbon Monoliths

Synthesis of Structure Controllable Carbon Aerogel with Low Drying Shrinkage and Scalable Size As High-Temperature Thermal Insulator

SYNTHESIS AND CHARACTERIZATION OF SILICA AEROGELS BY NON-SUPERCRITICAL DRYING METHOD

Structural Analysis And Control Of Ultralow Density Silica Aerogels Prepared By Sol-Gel Process