Abstract:Diffusion bonding of additive manufactured (AM) metal parts to traditionally manufactured metal parts could simultaneously achieve large-scale, complex-structure, and multi-material parts. However, there is a lack of study on diffusion bonding as well as its interface formation mechanism between AM metal parts and traditionally manufactured metal parts. In this study, diffusion bonding was performed to join AM 316L stainless steel and casting 45 steel at different temperatures. The element distribution, interface characteristics and shear strength of the joints were investigated, and the interface formation mechanism at different bonding temperature was analyzed in detail. The results reveal that the interface transition zone from the AM 316L steel side to the 45 steel side is composed of the metallic elements diffusion layer and the carbide layer. Moreover, an increase in bonding temperature can effectively promote interface voids closure and increase the thickness of the metallic elements diffusion layer, while the thickness of the carbide layer firstly increases and then decreases as the temperature increases. The component of the carbide layer was identified as brittle compounds (CrFe)23C6 and (CrFe)7C3. The shear strength of the joints exhibited an increasing trend with the increasing bonding temperature. Interestingly, a sudden decrease in strength was found at 950 °C due to the significant increase of the brittle carbide layer, while high-quality joints could be achieved as the brittle carbides dissolve at 1000 °C. This study could lay the foundation for understanding diffusion bonding interface behaviors between AM metal parts and traditional casting metal parts.

Study of Interface Diffusion and Reaction Between Zr3N4 and Stainless Steel

Study on interface behavior of Be/CuCrZr alloy by diffusion bonding

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

A Study of Interface Diffusion and Reaction of Ti/ZrN2/Si Film

Interface Diffusion and Chemical Reaction on the Interface of a PZT Film/si(iii) Sample During Annealing Treatment in N2 and Vacuum

Analysis on behaviors of contact reaction between quenched Al-Cr foils and stainless steel

Growth and Annealing of Zn-Mg Alloy Thick Films on Steel

Interface Behaviors and Mechanical Properties of Diffusion Bonded 45 Steel/additive Manufactured 316L Steel Joints

Design of amorphous-nanocrystalline films of TiAlCrNbZr x multi-component alloy: The effect of Zr on the corrosion resistance and mechanical properties

Study on Recrystallization and Etching Performance of FeNi42 Alloy with Trace Zr

Enhancing corrosion and mechanical properties of 304 stainless steel by depositing and annealing Zr75Cu25 thin-film metallic glass

On the thermal coarsening and transformation of nanoscale oxide inclusions in 316L stainless steel manufactured by laser powder bed fusion and its influence on impact toughness

Microstructure, Properties and Mechanism of Formation of Aluminum Diffusion Coatings on Heat-Resistant Stainless Steels

Effect of Zr on static recrystallization of deformed austenite and strain-induced precipitation in Ti microalloyed steel

Inter-Diffusion of Mg and Zn in Vacuum-Evaporated Mg Films on Zn Coated Steel Substrates

Influence of Zr on grain orientation, texture, and mechanical properties in hot- and warm-rolled FeCrAl alloys

Aes Study On The Interface Diffusion And Reaction Between Cr Layer And Si3n4/Si Substrate

Microstructure evolution and interdiffusion behaviour of Cr/Mo coated Zr-4 alloys at 1330 °C-1500 °C

Microstructure and Corrosion Resistance of Zn-Al Diffusion Layer on 45 Steel Aided by Mechanical Energy

Microstructure evolution and mechanical property of high temperature solid-state diffusion bonded Cr-Zry4 with and without a 316 SS interlayer

Study on RE-Al-Zr-C-N Coating by X-ray Photoelectron Spectroscopy