Abstract:Bisphenol A dicyanate (BADCy) resin microparticles were prepared by precipitation polymerization synthesis and were homogeneously dispersed in a BADCy prepolymer matrix to prepare a BADCy self-reinforced composites. The active functional groups of the BADCy resin microparticles were characterized by Fourier transform infrared (FT-IR) spectroscopy. The results of an FT-IR curve showed that the BADCy resin microparticles had a triazine ring functional group and also had an active reactive group -OCN, which can initiate a reaction with the matrix. The structure of the BADCy resin microparticles was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). From the TEM results, the BADCy resin microparticles dispersed in the solvent were nano-sized and distributed at 40-60 nm. However, from the SEM results, agglomeration occurred after drying, the BADCy resin particels were micron-sized and distributed between 0.3 μm and 0.6 μm. The BADCy resin prepolymer was synthesized in our laboratory. A BADCy self-reinforced composite was prepared by using BADCy resin microparticles as a reinforcement phase. This corresponds to a composite in which the matrix and reinforcement phase are made from different morphologies of the same monomer. The DSC curve showed that the heat flow of the microparticles is different from the matrix during the curing reaction, this means the cured materials should be a microscopic two-phase structure. The added BADCy resin microparticles as reaction sites induced the formation of a more complete and regular cured polymer structure, optimizing the cross-linked network as well as increasing the interplay between the BADCy resin microparticles and prepolymer matrix. Relative to the neat BADCy resin material, the tensile strength, flexural strength, compressive strength and impact strength increased by 98.1%, 40.2%, 27.4%, and 85.4%, respectively. A particle toughening mechanism can be used to explain the improvement of toughness. The reduction in the dielectric constant showed that the cross-linked network of the self-reinforced composite was more symmetrical and less polar than the neat resin material, which supports the enhanced mechanical properties of the self-reinforced composite. In addition, the thermal behavior of the self-reinforced composite was characterized by thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMTA). The results of DMTA also establishes a basis for enhancing mechanical properties of the self-reinforced composite.

Preparation and Characterization of Composites: Epdm-G-Aa/Caco3

Preparation and Characterization of Composites: Ethylene–propylene–diene Terpolymer‐graft‐maleic Anhydride/caco3

The Preparation of Polyethylene/Collagen Composites by Using Reactive Compatibilization Process

Mechanism and surface characteristics of polyacrylic acid-coated ultra-fine CaCO3

Fully Aminated Rigid‐rod Aromatic Polyamide Efficiently Reinforces Tetraglycidyl Diamino Diphenyl Methane Epoxy Resin and Its Carbon Fiber Composite

Preparation and Characterization of EPDM Composite Crosslinked with Titanium Dioxide

Preparation of Poly(methyl Methacrylate)/ultrafine CaCO3 Composite Particles by In-Situ Dispersion Polymerization

Modification of EPDM by CaCO_3 and ZDMA

Preparation and properties of EPDM/TiO2 composites

Photoinitiated Crosslinking of EPDM/inorganic Filler Blends and Characterization of Related Properties

Preparation and Properties of Gluten/calcium Carbonate Composites

Mechanical and Thermal Properties of Polypropylene (PP) Composites Filled with CaCO3 and Shell Waste Derived Bio-Fillers

Mechanical Properties and Carbonation Durability of Engineered Cementitious Composites Reinforced by Polypropylene and Hydrophilic Polyvinyl Alcohol Fibers

Mechanical and rheological properties of calcium carbonate-filled ethylene propylene diene elastomer reinforced by metallic acrylate salt

Study on the Preparation and Properties of Caco3/Polypropylene Composite Materials

Novel Preparation and Properties of EPDM/montmorillonite Nanocomposites

Effects of the Reinforcement and Toughening of Acrylate Resin/Caco3 Nanoparticles on Rigid Poly(Vinyl Chloride)

Preparation and Properties of Polyacrylamide/ Titanium Oxide Hydrogels

Low Dielectric Loss and Infrared Emissivity Coating with Enhanced Mechanical Property by Grafting Modification of EPDM

Study on the Relationships between Microscopic Cross-Linked Network Structure and Properties of Cyanate Ester Self-Reinforced Composites

Crystallization Behavior of PP in Composites with EPDM and a Surface Modified Nano-Calcium Carbonate