Abstract:This study investigates the interaction of polyacrylamide (PAM) of different functional groups (sulfonate vs. carboxylate) and charge density (30% hydrolysed vs. 10% hydrolysed) with calcium carbonate (CaCO3) via atomic force microscopy (AFM) and partly via molecular dynamic (MD) simulations. The PAM used were F3330 (30% hydrolysed), AN125 (25% sulfonated), and AN910 (% hydrolysed). A total of 100 ppm of PAMs was prepared in 0.1% NaCl, 3% NaCl, and 4.36% NaNO3 to be employed in AFM experiments, while oligomeric models (30 repeating units) of hydrolysed polyacrylamide (HPAM), sulfonated polyacrylamide (SPAM), and neutral PAM (NPAM) were studied on a model calcite surface on MD simulations. AFM analysis indicated that F3330 has a higher average adhesion and interaction energy with CaCO3 than AN125 due to the bulky sulfonate side group of AN125 interfering with SPAM adsorption. Steric repulsion of both PAMs was similar due to their comparable molecular weights and densities of the charged group. In contrast, AN910 showed lower average adhesion and interaction energy, along with slightly longer steric repulsion with calcite than F3330, suggesting AN910 adopts more loops and tails than the slightly flatter F3330 configuration. An increase in salt concentration from 0.1% to 3% NaCl saw a reduction in adhesion and interaction energy for F3330 and AN125 due to charge screening, while AN910 saw an increase, and these values increased further at 4.36% NaNO3. MD simulations revealed that the salt ions in the system formed salt bridges between PAM and calcite, indicating that the adhesion and interaction energy observed from AFM are likely to be the net balance between PAM charged group screening and salt bridging by the salt ions present. Salt ions with larger bare radii and smaller hydrated radii were shown to form stronger salt bridges.

Mechanism and surface characteristics of polyacrylic acid-coated ultra-fine CaCO3

The Mechanical and NIR Studies on Ultrafine Calcium Carbonate Treated by Four Surface Modifiers.

The Study on Mechanism, Interfacial Properties of PS-b-PAA Copolymer Coated Calcium Carbonate Particulate

Surface Energy Study Of Alooh Coated Calcium Carbonate By Inverse Gas Chromatography

Minicrystal And Xps Analysis Of Sio2 Coated Superfine Caco3 Powder

Effect of Oleic Acid-modified Nano-CaCO3 on the Crystallization Behavior and Mechanical Properties of Polypropylene

Combined Effect of Ion Concentration and Functional Groups on Surface Chemistry Modulated CaCO3 Crystallization

Preparation of Poly(methyl Methacrylate)/ultrafine CaCO3 Composite Particles by In-Situ Dispersion Polymerization

Surface Modification Of Caco3 With Dendritic Carboxylic Acids

Surface Modification and Adsorption Mechanism of Nanometer CaCO3

Surface coating of anhydrite powders with CaCO3 nano-particles prepared in Ca(OH)2-H2O-CO2 system

Preparation and Characterization of Composites: Epdm-G-Aa/Caco3

Adsorption of poly acrylic acid onto the surface of calcite: an experimental and simulation study

Improvement of Polyacrylate Coating by Filling Modified Nano-Tio2

Investigation of the mechanism of CaCO3 crystallization controlled by polymer lattices P(St-co-MAA)

On the crystallization of calcium carbonate modulated by anionic surfactants

Mechano-activated Surface Modification of Calcium Carbonate in Wet Stirred Mill and Its Properties

The synthesis of silica-polyacrylate nano-complex coating

Study on Surface Modification of Nano-Calcium Carbonate in Ethanol and Its In-situ Composite

Atomic Force Microscopy and Molecular Dynamic Simulation of Adsorption of Polyacrylamide with Different Chemistries onto Calcium Carbonate

Influence of low-molecular-weight and macromolecular organic additives on the morphology of calcium carbonate