Abstract:Airborne ultrasonic testing of lightweight, structured composite materials enables fast and contact-free non-destructive testing in aerospace and avoids material degradation due to contact with a coupling liquid. Established resonant air-coupled transducers consist of piezocomposite materials and several matching layers or more advanced materials like charged cellular polypropylene. The relaxation time and the specific frequency of such mechanical ultrasound emitters limit the spectrum of applications for each device. A short pulse length is key for reliable defect detection and each component at test can be best characterized at material- and geometry-specific frequencies. Here we show that focused thermoacoustic transducers are suited for testing lightweight, structured composite plates. Since the ultrasound is generated in air, these transducers show no resonance behavior and emit a broadband acoustic spectrum between 1.2 kHz and 1 MHz. Composite specimens of 3 mm to 9 mm thickness made of polylactide with a honeycomb structure were tested. Flat bottom holes were introduced to quantify the spatial resolution of the imaging method inside the strongly anisotropic specimen. As no broadband receivers are available yet, cellular polypropylene transducers were used as receivers, which limits the bandwidth of the method towards the bandwidth of the receiver. Nevertheless, we demonstrate the competitiveness of the thermoacoustic transducer compared to mechanical emitters at their respective resonance frequencies. Because a thermoacoustic transmitter features a nearly ideal pulse width, a single transmitter can be coupled with receivers with different resonance frequencies. With the development of broadband ultrasound receivers, air-coupled ultrasound spectroscopy will likely be possible in the near future. The analyzed transducer holds the potential to speed up testing during production and maintenance in aerospace and automotives. Its combination with a broadband receiver could also expand the application field of air-coupled ultrasonic testing from a qualitative error detection towards a quantitative, spatially resolved analysis of mechanical material properties.

Improvement of bulk acoustic wave hammer for vibration testing of microstructures using 1-3 composite transducers

A Planar Fabricated 1-3 Composite Ultrasonic Transducer to Determine the Dynamic Response of Microstructures

Novel Bulk Acoustic Wave Hammer to Determinate the Dynamic Response of Microstructures Using Pulsed Broad Bandwidth Ultrasonic Transducers

Determining the in-plane and out-of-plane dynamic response of microstructures using pulsed dual-mode ultrasonic array transducers

Finite element method simulation, design, and fabrication of micromachined high-frequency piezoelectric composite with hexagonal pillars for intravascular ultrasound imaging

Feasible Optimization and Fabrication of Multi-dimension Composites for High Frequency Ultrasonic Transducer

New 1-3 type piezoelectric composite material for kilohertz frequency range transducers

Design and Fabrication of 1-3 Piezoelectric Composite Material Air Coupled Ultrasonic Transducer

The thermoacoustic effect and its application in air-coupled testing of composite structures

Design of a novel 2D ultrasonic transducer for 2D high-frequency vibration–assisted micro-machining

Study of 1-3-2 type piezoelectric composite transducer array

Investigation of a Multi-Element Focused Air-Coupled Transducer

Novel multi-layer-composites design for ultrasonic transducer applications

Fabrication of Radial Array Transducers Using 1-3 Composite via a Bending and Superposition Technique

Design and Analysis of Ultrasonic Composite Transducer with a Quarter-wave Taper Transition Horn

Design Simulation of Composite Transducers

Finite Element Analysis and Experimental Studies on the Thickness Resonance of Piezocomposite Transducers

Design and Characteristics Study of Longitudinal–Torsional Piezoelectric Ultrasonic Transducers

Increasing Performances of 1–3 Piezocomposite Ultrasonic Transducer by Alternating Current Poling Method

Research on the electro‐elastic properties of the 2‐1‐3 (a revised version of 1‐3‐2) piezoelectric composite by finite element method

Analysis of electromechanical characteristics of the 1-3-2 piezoelectric composite and 1-3-2 modified structural material