Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

High-press preparation and thermoelectric properties of Bi0.90Sb0.10

Ultrasonic-assisted Hot Pressing of Bi2Te3-based Thermoelectric Materials

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Thermoelectric and thermomechanical properties of the hot pressed polycrystalline Bi0.5Sb1.5Te3 alloys

Effect of Starting Powder Particle Size on the Thermoelectric Properties of Hot-Pressed Bi0.3Sb1.7Te3 Alloys

Unprecedented Metallic BiS Phase from the Binary Bi–S Family Revisited under Extreme Conditions of High Pressure and High Temperature

High Mechanical Property and Texture Degree of Hot−Extruded Bi0.905Sb0.095

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Effect of Preparation Methods on Thermoelectric Properties of N-type Bi_2Te_(2.4)Se_(0.6) Bulk Alloys

High Pressure Synthesis, Structure and Thermoelectric Properties of Bicucho(Ch = S, Se, Te)

Microstructure and thermoelectric performance evaluation of p-type (Bi, Sb)2Te3 materials synthesized using mechanical alloying and spark plasma sintering process

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Nanostructured Bi2-Xcuxs3 Bulk Materials With Enhanced Thermoelectric Performance

High-Temperature Mechanical and Thermoelectric Properties of p-Type Bi0.5Sb1.5Te3 Commercial Zone Melting Ingots

Preparation and Sintering Behaviour of Nanostructured SrBi2Ta2O9ceramics

Thermoelectric and Mechanical Properties of Nano-Sic-dispersed Bi2Te3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Enhancement in thermoelectric performance of hydrothermally synthesized Ca and Sb co-doped Bi 2 Te 3 nanostructures

Thermoelectric Properties of Xpbte/yb0.2co4sb12 Hot-Pressed Samples

Ab initio study of the mechanical properties and thermal conductivity of Bi2O2X (X = Se, Te) under pressure

Bulk Nanocrystalline Thermoelectrics Based on Bi-Sb-Te Solid Solution

A method of shape description by a distribution function