Abstract:Titanium alloys are known for being difficult to machine. Within the groups of Ti alloys, the machinability is reduced when going from the α-alloys, to α + β, and finally to near-β or β-alloys. Uncoated cemented carbide is traditionally used for machining these alloys and finding a suitable coating to improve the performance is a challenge due to the high strength of Ti alloys and the high chemical reactivity of Ti with tool and coating materials at the temperatures achieved during cutting. The PVD applied Ti x Al 1-x N (x = 0.4–0.7) is generally recommended for machining Ti alloys and a top layer of NbN has shown promising performance in milling applications. This study systematically explores the wear mechanisms of either uncoated WC-12%Co or its Ti 0.45 Al 0.55 N-NbN coated version in the milling of Ti alloys ranging from near-α (Ti-6Al-2Sn-4Zr-2Mo), α + β (Ti-6Al-2Sn-4Zr-6Mo), and near-β (Ti-5Al-5Mo-5 V-3Cr) alloys. The wear evolution is explored by studying as-worn tools and their cross-section using SEM-XEDS and EBSD after having reached 10%, 30%, 50%, and 100% of the full tool life at a flank wear criterion VB = 200 μm. The coating is removed within seconds of engagement and fails by cracking within the bulk and PVD droplet defects can initiate such cracks. Diffusional dissolution of the coating may be active on a minor scale, but the rapid mechanical failure shows the need for a more robust coating formulation. Exposed cemented carbide is worn at varying intensities when machining the Ti alloys. The highest wear rate is achieved in milling α + β Ti-6246, followed by a moderate wear rate in near-β Ti-5553, and with a slower wear rate in milling near-α Ti-6242 which is explained varying intensities in oxidation wear, diffusional dissolution, and mechanical cracking. Diffusional loss of C gives rounder WC grains and remaining W at the interface is removed by the chip flow. Diffusional loss of Co gives reduced grain bonding and loss of the dampening effect that leads to fractures in WC grains. Specifically in milling α + β Ti-6246 and in minor scale in near-α Ti-6242, there is formation of CoWO 4 ceramic present several μm into the tool and its formation is facilitated by the oxidation of binder with resolved W. Fractures within the CoWO 4 explains the high wear rate. Cracks also propagate in binder regions initiated from weakened interface regions due to diffusional loss of C and Co.

Research on Failure Mechanism of Fine Grain Cemented Carbide Tool in Milling of Titanium Alloy

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Research on breakage characteristics in side milling of titanium alloy with cemented carbide end mill

Mechanism of Saw-Tooth Chip Formation of Titanium Alloy Based on Finite Element Simulation

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling

Multi-pattern failure modes and wear mechanisms of WC-Co tools in dry turning Ti–6Al–4V

Experimental Study on the Optimization of Ti1023 Milling Parameters

Research on cutting performance and tool life improvement methods of titanium alloy ultra-high speed milling tools

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

Investigation on the Performance of Spark Plasma Sintered Ultrafine WC-Co Cemented Carbide End Mills During High-Speed Precision Milling of Ti-6Al-4V Alloy

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Analysis of High Temperature Wear Process Mechanism of Cemented Carbide Tool

Study on wear mechanism of milling cutter and hole-making quality in ball helical milling process

Investigation on Generation and Features of Burn Defect in Ti6al4v Milling

Inlfuences of Material Tool and Tool Wear on Cutting Temperature of Turning Titanium Matrix Composites

Finite element analysis of Ti 1-x Al x N coated tools cutting performance and tool wear during Ti-6Al-4V milling

Effect of Surface-Textured AlSiTiN Coating Parameters on the Performance of Ball-End Milling Cutter in Titanium Alloy Milling

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V

Investigation on the high-feed milling of M28

Cutting Tool Selection and Cutting Parameter Optimization of Titanium Alloy Rough Milling

Effects of tool coating and tool wear on the surface and chip morphology in side milling of Ti2AlNb intermetallic alloys