Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Research on cutting performance and tool life improvement methods of titanium alloy ultra-high speed milling tools

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Research on drilling performance and tool life improvement methods of titanium alloy ultra-high-speed drilling bits

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Experimental Study on the Optimization of Ti1023 Milling Parameters

Tool Quality Life during Ball End Milling of Titanium Alloy Based on Tool Wear and Surface Roughness Models

Investigation on cutting forces and tool wear in high-speed milling of Ti-6Al-4V assisted by longitudinal torsional ultrasonic vibrations

Effect of Surface-Textured AlSiTiN Coating Parameters on the Performance of Ball-End Milling Cutter in Titanium Alloy Milling

Influence of cutting velocity on surface roughness during the ultra-precision cutting of titanium alloys based on a comparison between simulation and experiment

Study on design of conical arc side-edge milling cutter and cutting performance under ultrasonic-assisted condition

Machinability improvement of titanium alloys in ultra-precision machining with micro-structured surface

Study on Numerical Simulation and Experiment of Titanium Alloy for High Speed Milling

Effect of cutting conditions on the serrated chip formation in high-speed cutting

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

Effects of shear thickening fluid preparation on tool performance in the milling of Ti6Al4V titanium alloy

Cutting Tool Selection and Cutting Parameter Optimization of Titanium Alloy Rough Milling

Research on cutting force and surface integrity of TC18 titanium alloy by longitudinal ultrasonic vibration assisted milling

Optimizing the micro-texture and cutting parameters of ball-end milling cutters to achieve milling stability

Study of surface integrity of milled gamma titanium aluminide

Numerical Investigation on the Effect of Cutting-Edge Shape Factor on the Cutting Performance of Titanium Alloy