Abstract:For development of thin bioactive coatings on metal implants, a dense and uniform apatite layer was coated onto titanium (Ti) implants in situ by using a new biomimetic method, which is composed of apatite nucleation and growth steps in simulated body fluid (SBF). Analysis of the coatings by thin film X-ray diffraction and scanning electron microscopy-energy dispersive X-ray microanalysis (SEM-EMPA) before implantation showed that its characteristics were very similar to those of natural bone. The coated and uncoated rectangular plates were bilaterally implanted into the tibial proximal metaphyses of rabbits. After 6, 10 and 25 weeks post-implantation, the bone bonding and bone formation at the bone-implant interfaces were evaluated by a detachment test and undecalcified histological examination. Mechanical testing in tension showed that the failure load of apatite layer-coated Ti implants was significantly higher than that of uncoated control at each time period (all P < 0.001). Histologically, it was shown that bone was deposited directly onto the apatite coating without any intervening soft tissue, while in the paired controls, interpositional soft tissue was seen at the bone-implant interface. By SEM-EPMA, a uniform calcium- and phosphorus-rich layer was detected between the coated implants and bone, but not in uncoated controls at either earlier or later time periods. The results indicate that the apatite layer deposited on Ti in situ may significantly increase the bone bonding strength by providing a bioactive surface, which allows for an early bone apposition to the implant. In addition, the apatite layer-coated Ti produced by the biomimetic process may fulfil the requirements of favourable thin coatings and strong adhesion at the metal-coating interface.

Photoexcited formation of bone apatite-like coatings on micro-arc oxidized titanium.

A Comparative Study of in Vitro Apatite Deposition on Heat-, H2O2-, and NaOH-treated Titanium Surfaces

Biomimetic Deposition of Apatite on Electrochemically Oxidized Titanium Substrates

Apatite deposition on thermally and anodically oxidized titanium surfaces in a simulated body fluid.

[Experimental Study of Fast Formation of Biomimetic Apatite Coatings on Pure Titanium Surface].

Longer-Term Mechanical And Biological Evaluation Of Titanium Alloy Coated With Apatite Layer

Apatite Layer-Coated Titanium for Use As Bone Bonding Implants

[Fast Formation of Biomimetic Apatite Coatings on Pure Porous Titanium Implant's Surface].

Preparation and mechanical and biological performance of the Sr-containing microarc oxidation layer on titanium implants

Osteoblast Responses to Thin Nanohydroxyapatite Coated on Roughened Titanium Surfaces Deposited by an Electrochemical Process.

Bioactive Composite Coating on Titanium Implants for Hard Tissue Repair

Synthesis and Properties of Hydroxyapatite-Containing Porous Titania Coating on Ultrafine-Grained Titanium by Micro-Arc Oxidation

Osteoblast Response to Porous Titanium Surfaces Coated with Zinc-Substituted Hydroxyapatite

Effects of Micro-Arc Oxidation Discharge Parameters on Formation and Biomedical Properties of Hydroxyapatite-Containing Flower-Like Structure Coatings

Bonding of Chemically Treated Titanium Implants to Bone.

Rapid structural evolution and bone inducing mechanism of the multilayer coating with silicon-doped hydroxyapatite crystals on the microwave water steaming-hydrothermally treated titania coating

One-Step Approach for the Fabrication and Characterization of Hydroxyapatite/Tio2 Composite Ceramic Coatings by Micro-Arc Oxidation in Situ on the Surface of Pure Titanium

Biomimetic Deposition of Hydroxyapatite by Mixed Acid Treatment of Titanium Surfaces

Improvement in the Morphology of Micro-Arc Oxidised Titanium Surfaces: A New Process to Increase Osteoblast Response

The biocompatibility of nanostructured calcium phosphate coated on micro-arc oxidized titanium.

Micro-Arc Oxidation in Titanium and Its Alloys: Development and Potential of Implants