Abstract:The capacitor mismatch among diverse defects caused by variations in the manufacturing process significantly affects the linearity of the capacitor array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, the variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor arrays of the two ADCs can be reconfigured to be connected to each other, so that the Cn of ADC1 can be connected with two of the Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total harmonic distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8 dB and 6.4 dB, respectively.

Analysis of Coupled High-resolution Charge Scaling DAC

Analysis and Modeling of Dynamic Error in Current-Steering DAC

Analysis and Modeling of the Glitch Error in Current-Steering D/A Converter

Design of Analog Circuits in Multi-Bit Quantized Audio DAC

Design of a 12 bit High-Stability Digital-to-Analog Converter

Considerations and Optimization of Measurement Accuracy of Capacitance in Nano-Scale Cmos Technology

A Parameter Design Method for High Performance LCLC-LC Compensated CPT Systems

An Area- and Power-Efficient I-Ref Compensation Technique for Voltage-Mode R-2r Dacs

A Design Method of Capacitor Arrays for High-Resolution SAR ADCs

A 1.5 Bit/s Pipelined Analog-to-Digital Converter Design with Independency of Capacitor Mismatch

Analysis for Drive Circuit and Improved Current Controller for Proportional Amplifier

Current Sharing Analysis and Evaluation of Parallel DC-Link Capacitors in Vehicle Motor Drive

Detailed Study of A 5v/1v, Four Stage Switched Capacitor Converter Suitable for Integration

A Capacitor Paring Technique for Capacitor Mismatch Reduction

Demystifying and Mitigating Code-Dependent Switching Distortions in Current-Steering DACs

Auxiliary Testability Design Schemes for CMOS DACs with Ultrahigh Sampling Rates

Analog-to-digital converter with non-linear capacitor compensation

Improved Analysis of Current-Steering DACs Using Equivalent Timing Errors

Error Analysis and System Design of High-Accuracy Pipelined A/D Converters

Charge-Compensation-Based Reference Technique For Switched-Capacitor Adcs

A Tunable Foreground Self-Calibration Scheme for Split Successive-Approximation Register Analog-to-Digital Converter