Abstract:The capacitor mismatch among diverse defects caused by variations in the manufacturing process significantly affects the linearity of the capacitor array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, the variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor arrays of the two ADCs can be reconfigured to be connected to each other, so that the Cn of ADC1 can be connected with two of the Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total harmonic distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8 dB and 6.4 dB, respectively.

A Capacitor Paring Technique for Capacitor Mismatch Reduction

A Calibration Technique Based on Frequency-Domain Characteristics for Pipelined ADCs

Capacitor mismatch calibration for SAR ADCs based on comparator metastability detection

A Maximum-Likelihood-Estimation-Based Digital Background Calibration Technique for Interstage Gain Error in Pipelined ADCs

Digital Background Calibration in Pipelined ADCs Using Commutated Feedback Capacitor Switching

A 12-Bit 3.7-Msample/s Pipelined A/D Converter Based on the Novel Capacitor Mismatch Calibration Technique

A capacitive mismatch calibration method for SAR ADCs based on TDC

Capacitor Recombination Algorithm Combined with LMS Algorithm in 16-Bit SAR ADC with Redundancy

A Calibration Scheme for a 800-Ms/s 14 Bit Pipelined ADC in 28-Nm CMOS

A calibration technique for mismatch of capacitor arrays in A/D and D/A converters

A New Capacitance-to-Frequency Converter for On-Chip Capacitance Measurement and Calibration in CMOS Technology

An Improved Capacitor Averaging Technique for Pipelined ADCs

A 1.5 Bit/s Pipelined Analog-to-Digital Converter Design with Independency of Capacitor Mismatch

A Simple Histogram-Based Capacitor Mismatch Calibration in SAR ADCs

A novel capacitor recombination calibration method applied to 18-bit SAR ADC

A Pipelined A/D Conversion Technique With Low Inl And Dnl

Capacitor Mismatch Calibration Method for SAR ADC with Minimum Area and Power Penalty

A statistics-based background capacitor mismatch calibration algorithm for SAR ADC

A Digital Calibration Technique with High Speed and Low Complexity

A New Calibration Technique for Pipelined A/D Converters

A Tunable Foreground Self-Calibration Scheme for Split Successive-Approximation Register Analog-to-Digital Converter