Abstract:In this study, three cationic surfactants (hexadecyltrimethylammonium chloride, hexadecyldimethylbenzylammonium chloride, and octadecyltrimethylammonium chloride) were used to modify montmorillonite and polyethylene (PE)/maleic anhydride grafted polyethylene (PE-g-MAH)/organic-montmorillonite (Org-MMT) nano-composites, prepared by two blending processes (direct-melt blending and solution blending). X-ray diffractometry and transmission electron microscopy were used to investigate the intercalation behavior and microstructure of composites. Mechanical properties were also tested. It was found that the intercalation effect of PE/PE-g-MAH/Org-MMT could be enhanced by increasing the content of PE-g-MMT, using the silicate modified by a cationic surfactant with a benzyl group or long alkyl chain, adopting the solution-blending method or using high-density polyethylene as matrix. The degree of crystallinity of composites and the crystalline thickness perpendicular to the crystalline plane [like (110) and (200)] decreased with increasing amounts of PE-g-MAH and, under certain prescription, the crystalline thickness of the composite made by the solution method was much smaller than that made by direct-melt blending. This clearly showed that Org-MMT and PE-g-MAH had a heterogeneous nucleation effect on crystallization of PE from the melt, resulting in a decrease of crystalline thickness, and the heterogeneous nucleation effect was more evident in the nanocomposite made by the solution-blending method than in that made by the direct-melt intercalation process. The tensile strength initially increased and then decreased with increasing contents of PE-g-MAH. The maximum value in tensile strength (23.3 MPa) was achieved when the concentration of PE-g-MAH was 6 wt %. The impact strength increased concomitantly with the content of PE-g-MAH; it was 122.2 J/m when the concentration of PE-g-MAH was 9 wt %. (C) 2004 Wiley Periodicals, Inc.

Studies on characterization and cryogenic mechanical properties of polyimide-layered silicate nanocomposite films

Investigation of polyimide–mica hybrid films for cryogenic applications

Preparation and Dielectric Properties of Polyimide/silica Nanocomposite Films Prepared from Sol–gel and Blending Process

Synthesis and cryogenic properties of polyimide–silica hybrid films by sol–gel process

PREPARATION AND STUDY ON STRUCTURE OF THE POLYIMIDE/SILICA HYBRID AND NANOCOMPOSITE FILMS

Cryogenic Mechanical and Electrical Properties of Polyimide Nanocomposites

Exfoliated PS/MMT nanocomposites prepared by emulsion polymerization

Dielectric Properties of Polyimide‐Mica Hybrid Films

Polyimide-Surface-Modified Silica Tubes: Preparation and Cryogenic Properties

Poly(etherimide)/montmorillonite nanocomposites prepared by melt intercalation: morphology, solvent resistance properties and thermal properties

Preparation and properties of montmorillonite/organo-soluble polyimide hybrid materials prepared by a one-step approach

Electrical and Mechanical Property Study on Three-Component Polyimide Nanocomposite Films with Titanium Dioxide and Montmorillonite

Thermally Stable and Mechanically Strong Mesoporous Films of Poly(ether Imide)-Based Triblock Copolymers

Polyethylene/maleic Anhydride Grafted Polyethylene/organic‐montmorillonite Nanocomposites. I. Preparation, Microstructure, and Mechanical Properties

Aromatic Polyimide/MWCNT Hybrid Nanocomposites: Structure, Dynamics, and Properties

Polyimide/montmorillonite nanocomposites based on thermally stable, rigid-rod aromatic amine modifiers

Structure Characteristics and Dielectric Properties of PI/MMT Nanocomposite Films

Polyimide/mica hybrid films with low coefficient of thermal expansion and low dielectric constant

MECHANICAL PROPERTIES OF POLYIMIDE COMPOSITES FILLED WITH SiO2 NANO-PARTICLES AT ROOM AND CRYOGENIC TEMPERATURES

Preparation and Properties of Rigid‐rod Polyimide/silica Hybrid Materials by Sol–gel Process

Studies on Thermal and Mechanical Properties of Pi/Sio2 Nanocomposite Films at Low Temperature