Abstract:Neat polyimide films are known to be dense and rigid. They are therefore not suitable for use in membranes, sensors and sustainable energy storage applications. In this study, a novel technique has been used to simultaneously improve the porosity, rigidity, damping ability and impact resistance of polyimide membranes. It is demonstrated that dispersion of a small amount of polyaniline copolymer-modified clay of about 0.25-0.5 wt.% into the polyimide matrix resulted in an enhanced storage modulus while maintaining high damping ability and glass transition temperature, Tg. Novel polyimide/substituted polyaniline-copolymer-clay nanocomposite membranes containing poly(N-ethyl-aniline-co-aniline-2-sulfonic-acid)-modified-clay (SPNEAC) was successfully prepared and incorporated into the polyimide matrix to form modified clay/polyimide nanocomposites. UV-Vis analysis of the nanocomposite films shows that the optical transparency of the SPNEAC-PI nanocomposite membranes decreased with increasing SPNEAC concentration due to the high UV-Vis absorption of SPNEAC. Transmittance of about 3% was observed in the nanocomposite membrane containing 5 wt.% modified clay at 500 nm wavelength, which is significantly lower than that for the neat PI membrane of about 36%. The dispersion of SPNEAC containing a high concentration of clay (≥40 wt.% clay), in polyimide matrix, resulted in the attainment of a higher degree of imidization than was possible for the organoclay/polyimide nanocomposite. This behavior is believed to be due to the synergistic interaction between PI and SPNEAC. A correlation of the morphology and elastic modulus of the SPNEAC2/PI nanocomposites shows that at low loading of SPNEAC 2 ≤ 0.5 wt.%, the cross-sectional morphology of the composite is an open, spiky, weblike structure with a storage modulus of about 1 GPa, but it progressively evolves into densely packed microspheroids with storage moduli of ≥2 GPa at 10 wt.% SPNEAC2. The impact energy of SPNEAC/PI composites, calculated from the α-transition peak area, increased with increasing SPNEAC loading and were about 4 times that of neat PI at 10 wt.% SPNEAC.

Thermally Stable and Mechanically Strong Mesoporous Films of Poly(ether Imide)-Based Triblock Copolymers

In-situ Synthesis, Thermal and Mechanical Properties of Biobased Poly(ethylene 2,5-Furandicarboxylate)/montmorillonite (PEF/MMT) Nanocomposites

Mesoporous polyetherimide thin films via hydrolysis of polylactide-b-polyetherimide-b-polylactide

2021 pioneering investigator issue: mesoporous polyetherimide thin films <i>via</i> hydrolysis of polylactide-<i>b</i>-polyetherimide-<i>b</i>-polylactide

Poly(ethylene 2,5-Furandicarboxylate-mb-poly(tetramethylene Glycol)) Multiblock Copolymers: from High Tough Thermoplastics to Elastomers

Triblock copolymers of methyl methacrylate/N-vinyl pyrrolidone and their hydrophilication effects on poly(vinylidene fluoride) porous membranes

Preparation of High Density Polyethylene/polyethylene- Block -Poly(ethylene Glycol) Copolymer Blend Porous Membranes Via Thermally Induced Phase Separation Process and Their Properties

Solvent Resistant Self-Crosslinked Poly(ether Imide)

Mesoporous polyetherimide thin films <i>via</i> hydrolysis of polylactide-<i>b</i>-polyetherimide-<i>b</i>-polylactide

Polyhedral oligosilsesquioxane-modified boron nitride enhances the mechanical properties of polyimide nanocomposites

Mechanical properties of melt-fabricated, drawn films of A–B–A triblock copolymers of poly(l-lactide) (A) and two types of polyethers (B)

Synthesis and properties of modified thermoplastic polyimide films with good dielectric properties at high frequency and enhanced thermal stability via incorporation of rigid ester and biphenyl structural units

In Situ Determination of Mechanical Properties for Poly(Ether Ether Ketone) Film under Extreme Conditions

Synthesis and Characterization of Thermoplastic Polyether-imide Elastormer

Well-defined PE-b-PTFE Diblock Copolymers Via Combination of Coordination Chain Transfer Polymerization and Condensation Reaction: Facile Preparation and Surface Modification of Polyethylene Film

Preparation and Properties of Low Internal Stress Polyimide-b-Polysiloxane with a Hyperbranched Structure

Enhanced performance of low-dielectric siloxane-polyimide copolymers: Synthesis and properties

Flexible Ultrastrong 100-nm Polyethylene Membranes with Polygonal Pore Structures

Synthetically tunable polymers, free volume element size distributions, and dielectric breakdown field strengths

Polyether–polyimide Thermoplastic Elastomers. I. Synthesis and Properties

Fabrication of High Impact-Resistant Polyimide Nanocomposites with Outstanding Thermomechanical Properties