Designation of USB2.0 interface in data acquisition system

Xing Wei,Liu Kaihua

DOI: https://doi.org/10.3969/j.issn.1002-7300.2006.01.007

2006-01-01

Abstract:The way of how to realize the interface of data acquisition system based on DSP and USB is introduced in this paper.The designation of hardware interface and the program structure of the firmware is given.

What problem does this paper attempt to address?

Design of Data Communication Interface of Data Acquirement System Based on USB

陈章位,赵玉刚

DOI: https://doi.org/10.3321/j.issn:1004-132X.2004.20.014

2004-01-01

Abstract:An interface based on USB is designed for Data Acquirement System with DSP chips. Cypress EZ-USB technology and FPGA technology were used in this interface. This kind of interface can achieve high speed data communication between the Data Acquirement System and the PC in the USB 1.1 protocol, and it can meet the requirements of high speed and real-time requirements.
The Design of a Data Acquisition System Based on USB

DAI Hai-feng,FU Cui-yu

DOI: https://doi.org/10.3969/j.issn.1000-0682.2006.04.012

2006-01-01

Abstract:This paper presents the design of a data acquisition system based on the USB interface,which has its rational hardware structure and corresponding software.This system has been put into operation,which has produced a wonderful effect.
Design of Four-Channel High Precision Data Acquisition System with USB Interface

XUE Feng,LI Bin

DOI: https://doi.org/10.3969/j.issn.1000-3630.2007.05.025

2007-01-01

Abstract:The design of data acquisition system with high speed and high precision,which is based on USB (Universal Serial Bus),is introduced in this paper. A new audio A/D chip AKM5394 is applied to the data acquisition system. Using CPLD,FIFO,USB interface chip and two AKM5394,a four channel data acquisition system with high precision is implemented. The data are also saved and displayed in real time by USB interface on computer. The driving program,which is used for Windows 2000 or Windows XP,and the application program of the system are realized in Visual C++ language,and the firmware codes are programmed in C language. Because of low cost and a high performance,the system with a measuring precision up to 22 bit can be widely used in such fields as measuring control,signal analysis,and so on.
A Data Acqusition System Based on DSP and USB

JIANG Chao,LI Pei-yu

DOI: https://doi.org/10.3969/j.issn.1001-3881.2005.01.057

2005-01-01

Abstract:The structure of a data acquisition system based on DSP and USB chips was described.The interface between different modules was introduced,and the design of firmware used in USB was described.
Development of Data Acquisition and Processing System Based on DSP and USB 2.0

YU Ping,QIN Shu-ren

DOI: https://doi.org/10.3969/j.issn.1000-582x.2005.05.001

2005-01-01

Abstract:The data acquisition and processing system are proceeding towards faster, more powerful, easier to use and more cost effectiveness. This paper discuss the design of the high speed and convenient data acquisition and processing system based on DSP and USB 2.0, and expatiates the principle and method of the virtual instruments system in detail. The system employs an ADS8346 to sample the six channel signals simultaneously with a resolution of 16-bit.It utilizes EZ-USB FX2 as the USB2.0 interface, which can achieve the high speed communication between the host and the system. It uses TMS320VC33 (dsp) as the core chip, which can accomplish the function of the main control and real-time digital signal processing. The system enhances the virtual instruments' advantage more by the combination between software and hardware.
Design of the High Speed Real-time Data Acquisition System Based on USB 2.0

WANG Ping,SU Tao,FANG Haojun

DOI: https://doi.org/10.3969/j.issn.1004-373x.2007.01.029

2007-01-01

Abstract:To collect data and send the processed data to the PC in high speed,we design a high speed real-time data acquisition system based on USB 2.0.The paper introduces the hardware design of the system,the emphasis introduces the design of the firmware,driver and application program of the ISP1581.The system could complete data acquisition,processing and transmission very well,which is proved on a high speed DSP platform.
Real-time Bidirectional Data Transmission Based on USB Interface

Kuang Wang

2005-01-01

Abstract:The article designs a real-time bidirectional transmission channel.And it introduces the theory of the design,selects specific chip,introduces the hardware of the channel,and brings forward the method of designing USB firmware,driver,and application.
Designs of USB2.0 interface of data acquisition card

Qiao Liyan,Wu Jiangwei,Xu Hongwei

DOI: https://doi.org/10.3969/j.issn.1002-7300.2010.01.017

2010-01-01

Abstract:Data acquisition has been widely used in industrial production.Based on summarization of the hardware architecture,the thesis gives a detailed description of the design of USB interface,including the hardware design of USB2.0,The interface logic design in FPGA,USB firmware design,USB driver program design,and the application design.Through the experimental test,the result proves the design meets the accuracy and application objective expected,the data transporting rate is up to 20MB/s.
A data acquisition system based on usb2.0

Dai Guan-zhong

2005-01-01

Abstract:A data acquisition system based on USB2.0 is this paper, including the designing of hardware, firmware, drivers and application programs is presended. This system can realize analog signal sampling in 8 channels simultaneously and the input and output of switching signal in 16 binary channels. The USB interface control chip adopted is CY7C68013, a product of the Company of Cypress. Through designing the control logic of its GPIF interface, sampling and transmiting with high speed have been realized.
The Design of DSP High Speed Data Acquisition System Based on USB2.0 Protocol

Yu-hui BI,Cheng-jun HUANG,Can-xin GUO,Yong QIAN

DOI: https://doi.org/10.3969/j.issn.1009-0665.2006.05.016

2006-01-01

Abstract:On the purpose of portable high speed data acquisition,a high speed data acquisition system based on USB2.0 protocol was developed.It used the TI's C6000 series DSPs as the core part and realized the high data transfer speed by the USB interface chip.Details about the HPI(host-port interface) of DSP,the GPIF(general programmable interface) and endpoints of USB chip,the firmware program of USB chip,the application program of PC host and so on were depicted.The acquisition system was applied to partial discharge on-line monitoring,and realized the detection and reconstruction of partial discharge signals.
Application of USB2.0 in DSP debugging system

Guo Yulan,Ou Jianping,Chen Fubin,Zhang Jun

DOI: https://doi.org/10.3969/j.issn.1002-8978.2008.09.016

2008-01-01

Abstract:The article designed a data transfer system for DSP debugging system by using EZ-USB FX2 chip in order to solve the problem of data and command transfer between DSP and the host.It introduces the chip structure of FX2 and the Slave FIFO,and also brings forward the designing methods of hardware,USB firmware,driver program and application software.Practice results show that the system runs stably and reliably,and has a good application value.
Design and Application of Data Acquisition System Based on TMS320F2812 and USB

ZHANG Feng-jiang,WANG Xing-song

DOI: https://doi.org/10.3969/j.issn.1672-6413.2007.02.026

2007-01-01

Abstract:A multichannel data acquisition system was designed based on digital signal processor(DSP) and universal serial bus(USB) technology.The structure of the hardware and software was introduced,and the method of realization was described,the function was analysed.
Data communication based on USB interface of TMS320VC 5509 DSP

LENG Hua,LI Xin-ran,LI Zhi-jun,LI Cun-xiao

DOI: https://doi.org/10.3969/j.issn.1006-6047.2007.07.022

2007-01-01

Abstract:USB(Universal Serial Bus) is used in real-time mass data transfer between backstage PC and DSP-based data acquisition system.Using the internal USB module of TMS320VC 5509 DSP chip,the hardware interface circuit and control software are designed and the corresponding interface diagram and key codes are provided.The firmware of USB module is programmed with Visual C + +6.0 on Code Composer Studio and the Windows driver is developed with Driver Studio in backstage PC.The system designed is successfully used in substation for real-time data acquisition,meeting requirements of speed and real-time performance.
Design and Implementation of DSP and PC-High-Speed Data Transfer Interface

Gu Xueqiao,Li Jie,Xu Yinlin

DOI: https://doi.org/10.3969/j.issn.1672-1292.2009.04.015

2009-01-01

Abstract:A high-performance EZ-USB FX2 single-chip CY7C68013 is used as the USB interface,which realizes the high speed transmission of data between the DSP chip TMS320F2812 and PC.The paper introduces the hardware structure of the system,elaborates the design process of the work of CY7C68013 firmware SLAVE FIFO mode,and finally introduces a EZ-USB FX2-based single-chip high-speed data transmission application system.
Design of a High Speed Data Acquisition System Based on DSP and MAX1420

宋宇飞,吴乐南,李小平

DOI: https://doi.org/10.3969/j.issn.1674-6236.2009.11.045

2009-01-01

Abstract:This paper introduces the status of the data acquisition system,analyses the function demands of the high speed data acquisition system,and accomplishes the corresponding design scheme.The hardware of the system frame and the circuits of the main module are given in detail.The structure of the system software and the flow-chart of the main program are explained.In this system,MAX1420 is used as the analog to digital converter,DSP(TMS320C6713)as the CPU,FT245BM to realize the USB2.0 interface function,and large-capacity memorizer to backup the sampling data.The system testing shows that the system can real time complete the data acquisition and storage.
Data Transfer Design Based on Link Port and USB

郭裕兰,欧建平

DOI: https://doi.org/10.3969/j.issn.1672-2892.2009.03.001

2009-01-01

Abstract:To meet the data transfer requirement between DSP and host PC in multi-DSP debugging system,by using FPGA as the timing controller,a data transfer system based on Link port and USB2.0 interface is designed.Link port is employed to realize the data transfer between the DSPs,and also between DSP and FPGA.USB2.0 is used as the interface between FPGA and host PC.The system structure is introduced,the chips selection,the timing design of Link port and FX2 chip are also finished.The design methods of firmware program,driver program and application program are presented.This system can work stably and flexibly,which can fulfill the data transfer task between ADSP-TS101 and host PC very well.
Design of Multi-channel Data Acquisition and Real-time Display About USB2.0 Interface System

Chen Xin

2012-01-01

Abstract:Basic solutions to problems on matching the acquisition speed and processing speed are introduced.According to these solutions,the advanced application is designed for multi-channel USB2.0 data acquisition system,using Visual C+ +.NET 2005 application development platform.By using multithreading,circle buffer,GDI and double buffered graphics technologies,the system can display smooth scrolling or refreshing multi-channel waveforms without flicker while saving a large amount of data on hard disk.It can help researchers to understand the real-time data acquisition situation.

Computer Science
Design of high speed data sampling system based on FPGA and USB2.0

Wu Zhenyu,Chang Yubao,Feng Lin

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.z1.049

2006-01-01

Abstract:The paper introduces the using of FPGA and USB in the design of VI system based on data acquisition system.In the system,we use FPGA as control core.USB2.0 is used for interface to realize the fast data transmission between the FPGA and the PC.Through the combination of soft and hardware,a multichannel analogy signal and digital logic signal acquisition system are implemented.In addition,firware and USB device drive are also introduced.
Design of Visual Inspection System Based on DSP and USB Interface

边绍辉,蔡晋辉,周泽魁,张光新

DOI: https://doi.org/10.3969/j.issn.1000-3428.2004.20.074

2004-01-01

Abstract:A bottleneck of the real-time vision inspection system is the lower image processing velocity. DSP technology is applied to the field of computer vision. A USB based embedded vision inspection system using DSP and FPGA is discussed. And also, the configuration and the workflow of the system are presented in great detail.
Designs of the High-speed Data Acquisition System Based on USB and I2S Bus

LI Long-yu,FENG Zhi-hua,LIU Zhi-gang,ZHANG Chang-hui

DOI: https://doi.org/10.3969/j.issn.1001-2257.2005.05.016

2005-01-01

Abstract:This paper addresses a frame of highspeed data acquisition system which based on USB and I~2S bus.The using of highspeed data acquisition chip AD7862 and CPLD(complex programmable logic device) make the system adjustable.This method may be a good way for the D/A、DI/DO etc.

Designation of USB2.0 interface in data acquisition system

Design of Data Communication Interface of Data Acquirement System Based on USB

The Design of a Data Acquisition System Based on USB

Design of Four-Channel High Precision Data Acquisition System with USB Interface

A Data Acqusition System Based on DSP and USB

Development of Data Acquisition and Processing System Based on DSP and USB 2.0

Design of the High Speed Real-time Data Acquisition System Based on USB 2.0

Real-time Bidirectional Data Transmission Based on USB Interface

Designs of USB2.0 interface of data acquisition card

A data acquisition system based on usb2.0

The Design of DSP High Speed Data Acquisition System Based on USB2.0 Protocol

Application of USB2.0 in DSP debugging system

Design and Application of Data Acquisition System Based on TMS320F2812 and USB

Data communication based on USB interface of TMS320VC 5509 DSP

Design and Implementation of DSP and PC-High-Speed Data Transfer Interface

Design of a High Speed Data Acquisition System Based on DSP and MAX1420

Data Transfer Design Based on Link Port and USB

Design of Multi-channel Data Acquisition and Real-time Display About USB2.0 Interface System

Design of high speed data sampling system based on FPGA and USB2.0

Design of Visual Inspection System Based on DSP and USB Interface

Designs of the High-speed Data Acquisition System Based on USB and I2S Bus