Abstract:Viscosity is a physical property of fluids and shows resistance to flow. In metallurgical slag, it directly affects various parameters of a metallurgical process such as reaction rate, separation effect, etc. The estimation of viscosity by models during a production process is considered to be much more effective owing to the production fluctuations and complexities of the slag composition. Many viscosity models have been developed in the past, such as the structural model with a wide range of adaptability and complex calculation process and the empirical and semiempirical models with simple structure and a narrow range of adaptability. The present paper proposed a new method to calculate the structural parameter (NBO/T) ratio (the amount of nonbridging oxygen per tetrahedral-coordinated atom), based on which the relationship between the viscosity of molten slag and (NBO/T) ratio was investigated. First, the viscosity model was applied to SiO2–ΣMxO slags, with the model parameters obtained by fitting the viscosity data of pure oxide and SiO2–MxO binary slag, and the average deviations were in the range of 9%–18.5%. Then, the model was extended to calculate the viscosity of SiO2–Al2O3–ΣMxO, a multicomponent complex aluminosilicate system, and Al2O3 was split into acid and basic oxides. Then the oxides were used for calculating the (NBO/T) ratio and viscosity activation energy based on the amphoteric behavior of Al2O3 in SiO2–Al2O3–MxO ternary slag system. Using the parameters of a SiO2–MxO binary system, the model parameters of the Al2O3-containing slag system were obtained by fitting the viscosity data of the SiO2–Al2O3–MxO ternary slag system with average deviations between 10% and 25%. In addition, the viscosity of a multi-complex system (SiO2–Al2O3–CaO–MgO–FeO–Na2O–K2O–Li2O–BaO–SrO–MnO) and its subsystems were also calculated using the model proposed in this paper, and the average deviations is less than 25%, which shows relatively accurate prediction results. The present model is based on the analysis of a slag structure and processing of data by an empirical method. This method has a better prediction effect and wider application range compared with the traditional empirical model, and it uses a simpler calculation process compared with the structure model.

Relationship Between Liquid Structure and Property Iii-Residual Bond Theoretical Model

Relationship Between Liquid Structure and Property Ⅰ- Kinematic Viscosity of Magnesium Melt and Its Relationship with the Microstructure

Relationship Between Liquid Structure and Property Ⅱ—— Kinematic Viscosity of Mg-9Al Melt and Its Relationship with the Microstructure

Structure and Property of Metal Melt I: the Number of Residual Bonds after Solid-Liquid Phase Changes

Structure and Property of Metal Melt III—Relationship Between Kinematic Viscosity and Size of Atomic Clusters

Structure and property of metal melt IV—Evolution of titanium melt residual bond structure and its effect on dynamic viscosity

Close-contact Melting of Shear-Thinning Fluids

A theoretical method to calculate the viscosity of NaAlSi 3O 8 melt

Micro-Mechanism For The Evolution Of Viscosity Versus Temperature In Magnesium-Aluminum Alloy Melts

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Structure and Property of Metal Melt Ii-Evolution of Atomic Clusters in the Not High Temperature Range above Liquidus

EET Research on Melt Structural Information of Magnesium Alloy

Structurally-based Viscosity Model for Multicomponent Slag Systems

A NEW MODEL TO PREDICT THE VISCOSITY OF MULTI-COMPONENT METALLIC MELTS

Molecular configuration evolution model and simulation for polymer melts using a non-equilibrium irreversible thermodynamics method

A modified microscale viscosity model of polymer melts and experimental verification

Transferability of Interatomic Potentials with Insights into the Structure–property Relationship of SiO2–CaO–MgO–Al2O3 Melts

Non-Equilibrium Diffusion-Controlled Melting and Re-Solidification of Thin Metal Layers on a Reactive Substrate

An Integrated Model for Interaction Between Melt Flow and Non-Equilibrium Solidification in Thermal Spraying

Residual bond structure analysis of equilibrium phase diagram of Al-Si and Mg-Al alloys under pressure condition

The Structure and Transport Property of Liquid Al with Different EAM Model