Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Temperature dependence of the tribological mechanisms of amorphous PEEK (polyetheretherketone) under dry sliding conditions

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Study of Friction and Wear Characteristics of PEEK by Reciprocating Sliding Experiment and Temperature Dependences Simulation

Modeling of contact temperatures and their influence on the tribological performance of PEEK and PTFE in a dual-pin-on-disk tribometer

Loading Capacity of PEEK Blends in Terms of Wear Rate and Temperature

Effect of temperature on the tribological properties of Polytetrafluoroethylene/Kevlar fabric/phenolic composites

Thermal, Crystalline, and Tribological Properties of PEEK/PEI/PES Plastics Alloys

Role of transfer film formation on the tribological properties of polymeric composite materials and spherical plain bearing at low temperatures

Wear Evolution of the Glass Fiber-Reinforced PTFE under Dry Sliding and Elevated Temperature

Tribological Performance Study of Low-Friction PEEK Composites under Different Lubrication Conditions

Tribological Behaviour of Polymeric Coatings: II. SCF‐Reinforced PEEK Nanocomposite Systems

Effects of FDM parameters and annealing on the mechanical and tribological properties of PEEK

Tribology of self-lubricating high performance ATSP, PI, and PEEK-based polymer composites up to 300 °C

Determination of the Effect of Sliding Speed on Tribological Performances of Carbon Fiber Reinforced, Graphite and PTFE Filled Poly-ether-ether-ketone (PEEK) Polymer Composite

Effect of Low-Friction Composite Polymer Coatings Fabricated by Electrophoretic Deposition and Heat Treatment on the Ti-6Al-4V Titanium Alloy’s Tribological Properties

Comparative Study of Friction and Wear Performance of PEK, PEEK and PEKK Binders in Tribological Coatings

The influence of temperature on the tribological properties of polyoxymethylene (POM) materials

Effect of temperature on the friction and wear properties of a crosslinked and a linear polyimide

Effects of Friction Heat on Tribological Properties of UHMWPE

Sliding Wear of Polyetherimide Matrix Composites

Impact of thermo-oxidative aging on the dry tribological performance and wear mechanisms of UHMWPE/ZrO2 friction pairs