Abstract:Low costly ferritic stainless steels, especially the Cr2O3-forming alloys, are promising interconnect materials for solid oxide fuel cells (SOFCs) due to their thermal expansion compatibility with other cell components. However, the oxidation resistance of commercial ferritic stainless steels in the operating temperature range of 600-800 degrees C is not adequate, forming relatively thick, poorly conducting oxide scale on the surface of the stainless steel interconnect and decreasing the cell performance. Surface modification is necessary to improve the oxidation behavior and electrical property. The present study investigates the effect of a LaCoO3 protective coating by the sol-gel process on the intermediate temperature oxidation behavior of SUS 430 alloy, which is frequently considered as the interconnect material for SOFCs. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to characterize the phase structure, surface morphology and composition of the coating and the oxide scale. The "4-probe" method was employed to determine the area specific resistance (ASR) of the surface oxides. Long-term thermally cyclic oxidation at 750 degrees C in air has shown that the oxidation kinetics obeys the parabolic rule with a rate constant of K=4.18x10(-15) g(2)/(cm(4).s), which is 1-2 orders of magnitude lower than that of the uncoated alloy, the LaCoO3 protective coating effectively suppresses the formation of Cr2O3 and slows down the growth of MnCr2O4 spinel. As a result, the oxidation resistance and electrical conductivity of the coated SUS 430 alloy are significantly enhanced, resulting in an ASR at 750 degrees C of only 3.13 m Omega.cm(2) after oxidation at 750 degrees C for 850 h in air and an extrapolated ASR of 21.5 m Omega.cm(2) for 4 x 10(4) h oxidation.

Effects of La0.8Sr0.2Mn(Fe)O3-δ Protective Coatings on SOFC Metallic Interconnects

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

Evaluation of Lanthanum Ferrite Coated Interconnect for Intermediate Temperature Solid Oxide Fuel Cells

Effects of protective coating prepared by atmospheric plasma spraying on planar SOFC interconnect

LSM Protective Coatings on Stainless Steel As Interconnects for Solid Oxide Fuel Cells

Effect of Lacoo3 Coating on the Intermediate Temperature Oxidation Behavior of Sus 430 Metallic Interconnect

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

The Investigation of In-Situ Protection Effect of LaCo0.6Ni0.4O3-δ Cathode Contact Layer on High Temperature Oxidation of Fe-16Cr Alloy As Solid Oxide Fuel Cell Interconnect

Comparison of iron and copper doped manganese cobalt spinel oxides as protective coatings for solid oxide fuel cell interconnects

Fabrication of Co 3 O 4 and La 0.6 Sr 0.4 CoO 3−δ –Ce 0.8 Gd 0.2 O 2−δ dual layer coatings on SUS430 steel by in-situ phase formation for solid oxide fuel cell interconnects

Oxidation and electrical behavior of Ni-Mn3O4-La2O3-coated SOFC interconnect steel

Mn 1.4 Co 1.4 Cu 0.2 O 4 spinel protective coating on ferritic stainless steels for solid oxide fuel cell interconnect applications

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

La–Cr coating deposited by DC magnetron sputtering for solid oxide fuel cell interconnect applications

Effects of Mn concentration on durability of Fe-Cr ferritic steels dispersed with La 2 O 3 for solid oxide fuel cell interconnects

The Preparation and Properties of Ti(Nb)-Si-C Coating on the Pre-Oxidized Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

CrxN/Mn1.7Cu1.3 coating on ferritic stainless steel for solid oxide fuel cell interconnects

Dense Mn1.5Co1.5O4 coatings with excellent long-term stability and electrical performance under the SOFC cathode environment

Applying the Protective Mn–Co–La2O3 Coating on Crofer 22 APU Ferritic Stainless Steel Used as Solid Oxide Fuel Cell Interconnects