Abstract:A series of ceria-based composite materials consisting of samaria doped ceria (SDC) and binary carbonates(Li2CO3–Na2CO3) were examined as functional electrolytes for low-temperature solid oxide fuel cells (SOFCs). DTA and SEM techniques were applied to characterize the phase- and micro-structural properties of the composite materials. Conductivity measurements were carried on the composite electrolytes with a.c. impedance in air. A transition of ionic conductivity with temperature was occurred among all samples with different carbonate content, which related to the interface phase. Single cells based on the composite electrolytes, NiO as anode and lithiated NiO as cathode, were fabricated by a simple dry-pressing process and tested at 400–600°C. The maximum output power at 600°C increased with the carbonate content in the composite electrolytes, and reached the maximum at 25wt.%, then decreased. Similar trend has also shown at 500°C, but the maximum was obtained at 20wt.%. The best performances of 1085mWcm−2 at 600°C and 690mWcm−2 at 500°C were achieved for the composite electrolytes containing 25 and 20wt.% carbonates, respectively. During fuel cell operation, it found that the SDC-carbonate composites are co-ionic (O2−/H+) conductors. At lower carbonate contents, both oxide–ion and proton conductions were significant, when the content increased to 20–35wt.%, proton conduction dominated. The detailed conduction mechanism in these composites needs further investigation.

Fabrication of NiO-SDC Composite Anodes Using Gel-Casting for Low-Temperature SOFCs

Electrochemical performance of gel-cast NiO–SDC composite anodes in low-temperature SOFCs

Gel-cast NiO–SDC Composites As Anodes for Solid Oxide Fuel Cells

Ni/SDC Materials for Solid Oxide Fuel Cell Anode Applications by the Glycine-Nitrate Method

Preparation of Porous NiO-Ce0.8Sm0.2O1.9 Ceramics for Anode-supported Low-temperatureSolid Oxide Fuel Cells

A cathode-supported SOFC with thin Ce0.8Sm0.2O1.9 electrolyte prepared by a suspension spray

Ni1−Cu alloy-based anodes for low-temperature solid oxide fuel cells with biomass-produced gas as fuel

Preparation and Performance of Nanostructured Porous Thin Cathode for Low-Temperature Solid Oxide Fuel Cells by Spin-Coating Method

Low Temperature Solid Oxide Fuel Cells Based on Sm0.2Ce0.8O1.9 Films Fabricated by Slurry Spin Coating

Low-temperature co-sintering of co-ionic conducting solid oxide fuel cells based on Ce 0.8 Sm 0.2 O 1.9 -BaCe 0.8 Sm 0.2 O 2.9 composite electrolyte

Direct-Methane Solid Oxide Fuel Cells with Hierarchically Porous Ni-Based Anode Deposited with Nanocatalyst Layer

Co-Sintering of SDC / NiO-SDC Bi-Layers Prepared by Tape Casting

Preparation and characterization of nanocrystalline Ce0.8Sm0.2O1.9 for low temperature solid oxide fuel cells based on composite electrolyte

High Performance Ni–Sm2O3 Cermet Anodes for Intermediate-Temperature Solid Oxide Fuel Cells

Ni1-xCux alloy-based anodes for low-temperature solid oxide fuel cells with biomass-produced gas as fuel

A Hierarchical Porous Microstructure for Improving Long-Term Stability of Ni1-Xcux/Sdc Anode-Supported It-Sofcs Fueled with Dry Methane

Microstructures, conductivities, and electrochemical properties of Ce0.9Gd0.1O2 and GDC–Ni anodes for low-temperature SOFCs

Fabrication and Characterization of Large Size Anode Substrate of Solid Oxide Full Cell

Fabrication and Electrochemical Characterization of Anode-Supported Microtubular Solid Oxide Fuel Cells Based on Ce0.8sm0.2o2-D Electrolytes

Intermediate temperature solid oxide fuel cell composite cathodes consisting of nanostructured LSM and SDC particles

Development of Novel Low-Temperature SOFCs with Co-Ionic Conducting SDC-carbonate Composite Electrolytes