Abstract:A Ni/scandia-stabilized zirconia (ScSZ) cermet anode was modified by coating with nano-sized gadolinium-doped ceria (GDC, Gd0.2Ce0.8O2) prepared using a simple combustion process within the pores of the anode for a solid oxide fuel cell (SOFC) running on methane fuel. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed in the anode characterizations. Then, the short-term stability for the cells with the Ni/ScSZ and 2.0wt.%GDC-coated Ni/ScSZ anodes in 97%CH4/3%H2O at 700°C was checked over a relative long period of operation. Open circuit voltages (OCVs) increased from 1.098 to 1.179V, and power densities increased from 224 to 848mWcm−2, as the operating temperature of an SOFC with 2.0wt.%GDC-coated Ni/ScSZ anode was increased from 700 to 850°C in humidified methane. The coating of nano-sized Gd0.2Ce0.8O2 particle within the pores of the porous Ni/ScSZ anode significantly improved the performance of anode supported cells. Electrochemical impedance spectra (EIS) illustrated that the cell with Ni/ScSZ anode exhibited far greater impedances than the cell with 2.0wt.%GDC-coated Ni/ScSZ anode. Introduction of nano-sized GDC particles into the pores of porous Ni/ScSZ anode will result in a substantial increase in the ionic conductivity of the anode and increase the triple phase boundary region expanding the number of sites available for electrochemical activity. No significant degradation in performance has been observed after 84h of cell testing when 2.0wt.%GDC-coated Ni/ScSZ anode was exposed to 97%CH4/3%H2O at 700°C. Very little carbon was detected on the anodes, suggesting that carbon deposition was limited during cell operation. Consequently, the GDC coating on the pores of anode made it possible to have good stability for long-term operation due to low carbon deposition.

Ni1-xCux alloy-based anodes for low-temperature solid oxide fuel cells with biomass-produced gas as fuel

Ni1−Cu alloy-based anodes for low-temperature solid oxide fuel cells with biomass-produced gas as fuel

Low-temperature Solid Oxide Fuel Cells with Novel La0.6Sr0.4Co0.8Cu0.2O3−δ Perovskite Cathode and Functional Graded Anode

Fe Co0.5−Ni0.5–SDC Anodes for Low-Temperature Solid Oxide Fuel Cells

Ceria coated Ni as anodes for direct utilization of methane in low-temperature solid oxide fuel cells

Ni/SDC Materials for Solid Oxide Fuel Cell Anode Applications by the Glycine-Nitrate Method

Surface Tuned La 0.9 Ca 0.1 Fe 0.9 Nb 0.1 O 3-Δ Based Anode for Direct Methane Solid Oxide Fuel Cells by Infiltration Method

Fabrication of NiO-SDC Composite Anodes Using Gel-Casting for Low-Temperature SOFCs

Catalytic Modification of Ni–Sm-doped Ceria Anodes with Copper for Direct Utilization of Dry Methane in Low-Temperature Solid Oxide Fuel Cells

Direct-Methane Solid Oxide Fuel Cells with Hierarchically Porous Ni-Based Anode Deposited with Nanocatalyst Layer

A Hierarchical Porous Microstructure for Improving Long-Term Stability of Ni1-Xcux/Sdc Anode-Supported It-Sofcs Fueled with Dry Methane

Ni-Sm2o3 Cermet Anodes for Intermediate-Temperature Solid Oxide Fuel Cells with Stabilized Zirconia Electrolytes

A Robust NiO–Sm0.2Ce0.8O1.9 Anode for Direct-Methane Solid Oxide Fuel Cell

High-Entropy Alloys FeCoNiCuX (X = Al, Mo)-Ce 0.8 Sm 0.2 O 2 as High-Performance Solid Oxide Fuel Cell Anodes

Biomass Carbon Fueled Tubular Solid Oxide Fuel Cells with Molten Antimony Anode

High-performance Ni In-Situ Exsolved Ba(Ce0.9Y0.1)0.8Ni0.2O3-δ/Gd0.1Ce0.9O1.95 Composite Anode for SOFC with Long-Term Stability in Methane Fuel

High Performance Ni–Sm2O3 Cermet Anodes for Intermediate-Temperature Solid Oxide Fuel Cells

A cathode-supported SOFC with thin Ce0.8Sm0.2O1.9 electrolyte prepared by a suspension spray

Performance of Ni/Scsz Cermet Anode Modified by Coating with Gd0.2ce0.8o2 for an Sofc Running on Methane Fuel

Low Temperature Solid Oxide Fuel Cells Based on Sm0.2Ce0.8O1.9 Films Fabricated by Slurry Spin Coating

Enhanced Performance of Solid Oxide Fuel Cells with Ni/CeO2 Modified La0.75Sr0.25Cr0.5Mn0.5O3− Anodes