Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Nucleate Pool Boiling Heat Transfer of R134a and R134a-Pve Lubricant Mixtures on Smooth and Five Enhanced Tubes

Nucleate boiling heat transfer of R-134a and R-134a/POE lubricant mixtures on smooth tube

Pressure Drop and Heat Transfer of Flow Boiling R134a in a Dimpled Flat Duct

Experimental study on the pool boiling heat transfer of R134a outside various enhanced tubes

Study on Flow Boiling Heat Transfer Characteristics of R161/oil Mixture Inside Horizontal Micro-Fin Tube

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

The Boiling Heat Transfer Characteristics of the Mixture HFO-1234yf/oil Inside a Micro-Fin Tube

Investigation of the influence of POE oil on heat transfer to R134a and R1234ze(E) at enhanced tubes for pool boiling

Flow Boiling Heat Transfer Characteristic of Refrigerant R1234ze(E) in Horizontal Circular Tube

Experimental determination of the role of roughness and wettability on pool-boiling heat transfer of refrigerant

Effect of viscosity grade (POE) on the smooth-tube pool boiling performance with R-1234ze(E) refrigerant

Heat Transfer of R134a in a Horizontal Internally Ribbed Tube and in a Smooth Tube under Super Critical Pressure

Experimental investigation on the heat transfer performance of falling film evaporation with lubrication oil on horizontal tubes having different structures

Heat transfer enhancement of helical tubes during pool boiling

An Experimental Study of R134a Condensation Heat Transfer in Horizontal Smooth and Enhanced Tubes

R410A and R32 condensation heat transfer and flow patterns inside horizontal micro-fin and 3-D enhanced tubes

Condensation heat transfer and pressure drop of r134a in horizontal micro-scale enhanced tube

Flow Boiling Heat Transfer Characteristics in Horizontal, Three-Dimensional Enhanced Tubes

Condensation Heat Transfer Experiments of R410A and R32 in Horizontal Smooth and Enhanced Tubes

Experimental study of falling film evaporation of refrigerants, R32, R1234yf, R410A, R452B and R454B on horizontal tubes

Condensation heat transfer and pressure drop characteristics inside smooth and enhanced tubes with R410A and R32