Abstract:Advances in Mechanical Engineering, Volume 14, Issue 5, May 2022. Experimental investigations of the condensation and evaporation of R410A on the outside of two double-side enhanced heat transfer tubes were conducted, and the tube performance was compared with that of a smooth copper tube. The research object consisted of a smooth tube with a length of 2000 mm and an outer diameter of 25.4 mm and two double-side enhanced tubes of the same size. The evaporation experiments were run under the following conditions: the evaporation saturation temperature was 7°C, water inlet temperature was 8°C–18°C, and water flow rate was 0.6–1.6 m3/h. The condensation experiments were run under the following conditions: the saturation temperature was 35°C, water inlet temperature was 21°C–30°C, and water flow rate was 0.4–1.6 m3/h. During the data processing, the heat transfer coefficient of the water side was obtained using the Gnielinski-Wilson method, and that of the refrigerant side was obtained using the thermal resistance separation method. The effect of the surface structure on the heat transfer performance was analyzed, and a strengthening measure was proposed. The experimental results indicate that the evaporation heat transfer coefficients outside the smooth tube increased with the raise of the inlet water temperature, while the double-side enhanced tubes decreased; both the condensation heat transfer coefficients outside the smooth tube and the enhanced tubes increased with the increase of the water flow rate. Due to the different type of enhanced tube ribs, tube #3 surface structure is more conducive to the formation of vaporization core, which is about 30% higher than the outer heat transfer coefficient of tube #2. It is more in line with the requirements of strengthening horizontal single tube external pool boiling heat transfer. In the condensation experiment, the condensation heat transfer coefficients outside the smooth tube increased with the raise of the inlet water temperature, while the double enhanced tubes decreased; both the condensation heat transfer coefficients outside the smooth tube and the enhanced tubes increased with the increase of the water flow rate. With the analysis of the rib structure, the outer surface structure of tube #2 has stronger drainage capacity, and the external average condensation heat transfer coefficient is about 7% higher than that of tube #3, which is more in line with the requirements of condensing heat transfer outside the single tube.

Experimental investigation on the heat transfer performance of falling film evaporation with lubrication oil on horizontal tubes having different structures

Experimental Investigations of R134a and R123 Falling Film Evaporation on Enhanced Horizontal Tubes.

Experimental Study of the Falling Film Evaporative Cooling on Horizontal Tubes Plates

Nucleate boiling heat transfer of R-134a and R-134a/POE lubricant mixtures on smooth tube

Experimental Investigation of R410A and R32 Falling Film Evaporation on Horizontal Enhanced Tubes

Influence of Lubricant Oil on Heat Transfer Performance of Refrigerant Flow Boiling Inside Small Diameter Tubes. Part I: Experimental Study

Experimental Study of the Local and Average Falling Film Evaporation Coefficients in a Horizontal Enhanced Tube Bundle Using R134a

Investigation of the influence of POE oil on heat transfer to R134a and R1234ze(E) at enhanced tubes for pool boiling

Experimental research of frictional performance of R410A-oil mixture flow condensation inside a 5 mm internally spiral grooved enhanced tube

Falling Film Evaporation and Nucleate Pool Boiling Heat Transfer of R134a on the Same Enhanced Tube

HEAT TRANSFER OPTIMIZATION OF THE HORIZONTAL TUBE BUNDLES IN FALLING FILM EVAPORATORS

Effect of oil concentration, viscosity, and surface tension on tube temperature and heat transfer coefficients of R1234ze(E)/oil spray evaporation on an enhanced tube bundle

Falling film evaporation experiment and data processing method of R1234ze (E) on horizontal enhanced tubes

Experimental comparison on condensation and evaporation outside double-side enhanced horizontal tubes

Falling Film Evaporation Of Water On Horizontal Configured Tube Bundles

Experimental Study of Oil Retention in Microchannel Evaporators and Lubricant Effect on Heat Transfer and Distribution Performances with R32/Pve Mixture

Heat Transfer Characteristics of Falling Film Evaporation on Horizontal Tube Arrays

Experimental evaluation on flow boiling heat transfer of R290/POE-oil working fluid for absorption refrigeration in smooth horizontal tubes

Flow Resistance Characteristics of R410A-oil Mixture during Evaporation in a Small Diameter Enhanced Tube

Experimental Study of Evaporation Frictional Pressure Drop in Horizontal Enhanced Tube

Experimental Investigation of Evaporation Heat Transfer Inside Horizontal Micro-Fin Tubes