Abstract:Results are presented here from an experimental investigation on tubeside condensation and evaporation heat transfer that took place in three Vipertex stainless steel enhanced heat transfer tubes (1EHT-2, 2EHT-2 and 4EHT). Equivalent outer diameter of the tube was 9.52 mm (0.375 in) and the inner diameter was 8.32 mm (0.3276 in). The test apparatus included a horizontal, straight test section with an active length heated by water circulated in a surrounding annulus. Constant heat flux was maintained and refrigerant quality varied. Condensation experimental runs were performed using R410A as the working ﬂuid; over the inlet quality range of 0.2– 0.8; for mass ﬂux values that ranged from 150 to 460 kg/(m2 s). In a comparison of condensation heat transfer performance, the enhanced 1EHT-1 tube has best heat performance followed by the enhanced 4EHT tube and finally the 1EHT-2 tube. The highest pressure drop increase was seen in the 1EHT-1 tube followed by the 4EHT tube and the 1EHT-2 tube. The evaporation experiments were performed using R410A at a constant saturation temperature of 279 K; for a mass flux that ranged from 160 to 390 kg/(m2 s). Inlet and outlet vapor qualities were fixed at 0.2 and 0.8, respectively. As the mass velocity increased, the heat transfer coefficient and pressure drop penalty increase accordingly. Experimental results show a slightly larger pressure drop in the 1EHT-1 tube. The pressure drop in the three EHT tubes could be attributed to the dimples and protrusions in the surface structure, which produce an increased density of nucleation sites. In addition, it was found that the evaporation pressure drop increases with the increasing depth of the dimples. Condensation and evaporation performance is mainly due to the increase in the heat transfer surface area and the increase of interfacial turbulence; this produces ﬂow separation, secondary ﬂows and a higher heat ﬂux from the wall to the working ﬂuid. Enhanced heat transfer tubes are important options to be considered in the design of high efficiency systems. A wide variety of industrial processes involve the transfer of heat energy during phase change and many of those processes employ old technology. These processes are ideal candidates for a redesign that could achieve improved process performance. Vipertex enhanced tubes recover more energy and provide an opportunity to advance the design of many heat transfer products.

Experimental Study on Flow Evaporation Heat Transfer Characteristics Inside Horizontal Three-Dimensional Enhanced Tubes

Experimental Investigation of Flow Boiling Inside Three Three-Dimensional Surface Enhanced Heat Transfer Tubes

Evaporation Heat Transfer Characteristics of R410A Inside Horizontal Three-Dimensional Enhanced Tubes

Experimental Study on Condensation and Evaporation Flow Inside Horizontal Three Dimensional Enhanced Tubes

Experimental Study on Heat Transfer Performance and Flow Pattern in Micro-Fin Tubes and 1EHT Three-Dimensional Heat Exchange Tubes

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth and Three-Dimensional Enhanced Tubes

An Experimental Study on Flow Boiling Heat Transfer Outside Horizontal Enhanced Tubes

Condensation and Evaporation Heat Transfer Characteristics of Low Mass Fluxes in Horizontal Smooth Tube and Three-Dimensional Enhanced Tubes

Analysis of Condensation and Evaporation Heat Transfer Inside 3-D Enhanced Tubes

Experimental Study Of Condensation Flow Inside Horizontal Smooth, Herringbone And Three Enhanced Surface Tubes

Experimental Comparison of the Evaporation and Condensation Heat Transfer Coefficients on the Outside of Enhanced Surface Tubes with Different Outer Diameters

An Experimental Study of In-Tube Condensation and Evaporation Using Enhanced Heat Transfer (EHT) Tubes

Condensation and Evaporation Characteristics of Flows Inside Vipertex 1EHT and 4EHT Small Diameter Enhanced Heat Transfer Tubes

Evaporation Heat Transfer Characteristics On The Outside Of Horizontal Smooth, Herringbone And Enhanced Surface 1eht Tubes

Condensation Characteristics of Flows Inside the Three-Dimensional Enhanced and Smooth Tubes

An Experimental Investigation to Determine the Effect of Tube Material on the Tubeside Heat Transfer Performance of the Enhanced 1EHT Three Dimensional Heat Transfer Tube

EXPERIMENTAL STUDY ON HEAT FLUX EFFECT ON EVAPORATION IN TWO DIMPLE-GROOVED TUBES

Condensation Heat Transfer of R410A on Outside of Horizontal Smooth and Three-Dimensional Enhanced Tubes

Condensation and Evaporation Heat Transfer Characteristics in Horizontal Smooth, Herringbone and Enhanced Surface EHT Tubes

Condensation Characteristics of Flows in Newly Developed, Three-Dimensional Enhanced Heat Transfer Tubes

Comparison Of Evaporation And Condensation Characteristics Among Three Enhanced Tubes