Abstract:Polysulfide sealants have high resistance against ultra violet radiation and environment,exhibit good low-temperature properties,low water-vapor transmission,and resist against solvents and chemicals.They were many publications on the characterization of metal peroxides-cured polysulfide,reporting the results of thermogravimetry analysis,dynamic mechanical analysis,tensile strength and hardness test.Although the polysulfide rubber has the advantage of lower cost,they faced the strong challenges from silicone and polyurethane-based sealants.One of the main reasons is their relatively poor tensile properties and weak adhesive strength.The new multi-alkoxyorganosilane coupling agents with hydroxyl-amine group(MAGHA)are synthesized by addition of γ-aminopropyltriethoxysilane(KH550) and γ-glycidoxypropyltrimethoxysilane(KH560).The influence to the polysulfide sealants by the multi-alkoxyorganosilane coupling agents with hydroxyl-amine group as additive are studied.With a small amount of MAGHA,the commercial polysulfide-based sealants have significant improvement in mechanical properties.In our polysulfide composition,the methoxy or ethoxy can be reacted with hydroxyl on the surface of the filler.Hydroxy group of the new multi-alkoxyorganosilane coupling agents or water produced by oxidation between polysulfide and MnO2 can make MAGHA to create the three-dimensional structure of polysiloxane through MAGHA polycondensation.The three-dimensional structure of polysiloxane has ability to package the surrounding of fillers and enhance the chain of polysulfide sealant through interreacted pendent with hydroxyl-amine group of MAGHA which can improve the tensile strength and ultimate elongation of sealant simultaneously.The test results show that 1% of multi-alkoxyorganosilane coupling agents with hydroxyl-amine group could help increasing 30% in the ultimate elongation and 70% in the tensile strength of the polysulfide sealants.The adhesive strength to steel also increased significantly.Since MAGHA reinforcement significantly increased the bulk tensile strength of polysulfide sealants,while MAGHA has the special hydroxyl-amine structure,which is the foundation of epoxy resin for its high properties of adhesive.When KH560 added to polysulfide sealants,the adhesive strength has no significant changed.Dynamic mechanical thermal analysis shows the Tg of polysulfide sealant have increased about 5℃.It may due to the increased cross-link by the result of the new multi-alkoxyorganosilane coupling agents with hydroxyl-amine group effect to —SH and fillers.The movements of main chain are limited.It also increased the ability on water.From water absorption test,the polysulfide sealants added MAGHA appear excellent properties of water absorption and resistance.After 18-day immersion,the polysulfide sealants before modification absorbed more than 6.10% water,but only absorbed 4.20% water after modification.This due to the siloxane structure surrounding filler.And the results indicate that the introduction of the MAGHA has no appreciable influence on oil resistance of polysulfide sealants.This new kind multi-alkoxyorganosilane coupling agents with hydroxyl-amine group have the similar effect of modification to the other resins are expected.The continue work are going on.

The research of polysulfide sealant modified with inorganic fillers

The research of polysulfide sealant modified with composite fillers

Effect of filler on the compression set, compression stress-strain behavior, and mechanical properties of polysulfide sealants

Enhanced Sound Insulation and Mechanical Properties Based on Inorganic Fillers/thermoplastic Elastomer Composites

Modification of Polysulfide Sealant with Polysulfide Polythio-Urethane-Urea

Modification of polysulfide sealant with multi-alkoxyorganosilane coupling agents with hydroxyl-amine group

Study on the Curing and Thermal Aging Properties of Polysulfide Sealent

Improvement in Compression Performance of the Polysulfide Sealant by Thiol‐acrylate Reaction

Crystallization and Mechanical Properties of Polypropylene Filled with Sio2 Nanoparticles

Strengthening the mechanical properties of polysulfide adhesives by introducing polyurethane

Synthesis and properties of polysulfide sealant containing thio-urea

Preparation and Research of Hydrophobic PDMS/Nano-SiO2 Modified SiO2 Coating

Self-Healable and Reprocessable Polysulfide Sealants Prepared from Liquid Polysulfide Oligomer and Epoxy Resin.

Influences of different polysulfide rubbers on compressibility of polysulfide sealant

Compression Set Property And Stress-Strain Behavior During Compression Of Polysulfide Sealants

The Effect of Various Fillers on the Properties of Methyl Vinyl Silicone Rubber

Enhanced Properties of Poly(vinylidene Fluoride) with Low Filler Content SiO 2 -G-(mma-co-ba) Core-Shell Nanoparticles

Effect of different ceramic fillers filled with GF/PTFE on the tensile and compressive properties of the composites

Effect of nano-silica@ chitosan phosphate ester on the mechanical properties and water resistance of magnesium oxychloride cement

Crystallization Behavior and Dynamic Mechanical Properties of Poly(phenylene sulfide)/Nano-SiO_2 Composites

Mesoporous Spherical Silica Filler Prepared from Coal Gasification Fine Slag for Styrene Butadiene Rubber Reinforcement and Promoting Vulcanization