Abstract:In this paper, mechanical properties and microstructures of the cast and extruded Al-xCu-1Li-0.4Mg–1Zn-0.1Zr alloys (x = 2.0, 3.0, 4.0, 4.5, 5.5, 6.5 wt%) were investigated. The results showed that the as-cast micrographs of alloys with different Cu content primarily consist of dendritic α-Al grains, and the intermetallic phases at the grain boundaries were Cu and Zr rich phases. After solution treatment, no recrystallization took place in extruded alloys, and the alloys mainly represented mixed textures composed of <111> and <100> fibers. Cu significantly affected the precipitation behavior of the extruded alloys. Only T1 (Al2CuLi) phases were observed in T6 (aging at 175 °C for 32 h) and T8 (3% pre-strain followed by aging at 150 °C for 32 h) treated alloy with 2 wt% Cu. Further increasing Cu contents (4.5 and 6.5 wt%) enabled the co-precipitation of T1 and θ' (Al2Cu) phases, as well as increased their density. In addition, the microstructures of grain boundaries of alloys with different Cu content showed dramatic differences. T1 phases precipitated at the grain boundaries of alloy containing 2 wt% Cu, while rare precipitation of T1 phases was observed at the grain boundaries of alloy with 6.5 wt% Cu. The yield strength (YS) of the alloys increased with the Cu content and the elongation (EL) showed an opposite trend. A good combination of ultra-high strength (YS = 684 MPa, ultimate tensile strength = 726 MPa) and ductility (EL = 6.3%) was obtained in T8 treated alloy containing 4.5 wt% Cu. The presence of the undesired coarse T2 (Al6CuLi3) phases at the grain boundaries resulted in the premature failure of the high Cu content alloys.

The Influence of Extrusion Ratio on W-40 ％ Cu Alloy Produced by Powder Canning Hot Extrusion

The numerical simulation of powder canning hot extrusion of W-40Cu alloy

The influence of percentage composition of Cu on the properties of W-Cu alloy produced by hot extrusion

The Influence of Mechanical Milling on the Properties of W–40wt.%Cu Composite Produced by Hot Extrusion

Research on the densification of W–40 wt.%Cu by liquid sintering and hot-hydrostatic extrusion

Research on the densification of W-30 wt%Cu composite powder by hot extrusion with steel cup

Effect of Extrusion Ratio on Microstructure and Mechanical Properties of Mg–8Li–3Al–2Zn–0.5Y Alloy with Duplex Structure

Microstructure and Mechanical Properties of a Hot-Hydrostatically Extruded 93w–4.9ni–2.1fe Alloy

The influence of mechanical milling on microstructure and the properties of W-40Cu composite by hot extrusion

W-Cu Composites Subjected To Heavy Hot Deformation

Numerical simulation of hot hydrostatic extrusion of W-40wt.% Cu

Influence of Size and Distribution of W Phase on Strength and Ductility of High Strength Mg-5.1Zn-3.2Y-0.4Zr-0.4Ca Alloy Processed by Indirect Extrusion

Influence of Extrusion Ratio on Microstructure and Tensile Properties of Mg–Gd–Y–Zn–Zr Alloy

Effect of Extrusion Parameters on Microstructure and Mechanical Properties of Mg-7.5Gd-2.5Y-3.5Zn-0.9Ca-0.4Zr (wt%) Alloy

Microstructures and Mechanical Properties of Hot-extruded Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,1.5) Alloys

Effect of Extrusion on Microstructure and Properties of a Submicron Crystalline Cu–5 Wt.%cr Alloy

Influence of Extrusion Parameters on Grain Size and Texture Distributions of AZ31 Alloy

Densification of Mechanically Milled 3%C-Cu Composite Powders by Hot Extrusion

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Effects of Extrusion Ratio on the Microstructure, Texture and Mechanical Properties of Mg-2.5Nd-0.5Zn-0.5Zr Alloy Sheets

Microstructure and properties of tungsten copper produced by hot deformation densification technology