Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

The influence of percentage composition of Cu on the properties of W-Cu alloy produced by hot extrusion

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

The Influence of Extrusion Ratio on W-40 ％ Cu Alloy Produced by Powder Canning Hot Extrusion

Effect of Cu content and heat treatment on the properties and microstructure of W–Cu composites produced by hot extrusion with steel cup

The Influence of Mechanical Milling on the Properties of W–40wt.%Cu Composite Produced by Hot Extrusion

Research on the densification of W-30 wt%Cu composite powder by hot extrusion with steel cup

W-Cu Composites Subjected To Heavy Hot Deformation

Effects of Fe content on microstructure and properties of Cu–Fe alloy

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Co-deformation in Cu–6 Wt.% Ag Nanocomposites

Microstructure and properties of tungsten copper produced by hot deformation densification technology

The influence of mechanical milling on microstructure and the properties of W-40Cu composite by hot extrusion

Research on the densification of W–40 wt.%Cu by liquid sintering and hot-hydrostatic extrusion

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Effect of the rolling plastic deformation on microstructure and properties of W-Cu composite

Effect of Extrusion on Microstructure and Properties of a Submicron Crystalline Cu–5 Wt.%cr Alloy

Effects of Deformation on Microstructures and Properties of Submicron Crystalline Cu-5%Cr Alloy

Numerical simulation of hot hydrostatic extrusion of W-40wt.% Cu

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Microstructure and mechanical properties of high density tungsten alloy and its influence factors

Microstructure and Mechanical Properties of a Hot-Hydrostatically Extruded 93w–4.9ni–2.1fe Alloy