Minitype Electrical Network Monitoring System Based on CAN Communication

Jiang JianMing,Ma ZhengHua,Zhu ZhengWei

DOI: https://doi.org/10.3969/j.issn.1008-0570.2007.26.028

2007-01-01

Abstract:The collectivity scheme of minitype electrical network monitoring system, the circuit structure of metrical port and the connective technique of CAN net are all analyzed. The design and realization of bottom PC’s CAN communication are expiation.

What problem does this paper attempt to address?

The Design and Realization of PLC Remote Monitoring and Diagnosing System

韩思亮,汤建新,马皓

DOI: https://doi.org/10.3969/j.issn.1000-0682.2005.01.007

2005-01-01

Abstract:This paper introduces PLC remote monitoring and diagnosing system based on a new network method of linking serial server.It also puts emphasis on the communication principle to host computer,realtime communication and the design of freeport communication and center server.
Multi-node data acquisition and analysis system for the development of AT electronic control unit.

Wei Chen,Yong Zhai,Gang Tao,Yuefeng Ma

DOI: https://doi.org/10.1109/EMEIT.2011.6023711

2011-01-01

Abstract:In this paper, a multi-node data acquisition and analysis system for the development of AT ECU (electronic control unit)is designed. The system acquires data from each node on the bus and sends the data to PC through CAN card, while designing data display, storage and analysis system on PC through LabVIEW8.6 platform in order to monitor control signals and state parameters of the automatic transmission in real-time. This system can improve the efficiency of data processing and shorten the development cycle for ECU by analyzing the data acquired. © 2011 IEEE.
Tree-Based Intermittent Connection Fault Diagnosis for Controller Area Network

Leiming Zhang,Fan Yang,Yong Lei

DOI: https://doi.org/10.1109/tvt.2019.2929419

IF: 6.8

2019-01-01

IEEE Transactions on Vehicular Technology

Abstract:Controller area network (CAN) is the most widely adopted network protocol in vehicle communication systems. The intermittent connection (IC) fault, a random cable connectivity problem with short durations, occurring in the CAN network may result in system performance degradation and system level failures in severe cases. Therefore, the health management of CAN-based networked systems demands effective detection and accurate localization of the IC fault. However, the diagnosis of IC fault in CAN network has not been fully exploited. This paper proposes a novel tree-based IC fault diagnosis method to identify the various IC fault locations in the CAN network. First, the error event pairs for network nodes are defined by analyzing the data-link layer information upon each error. Then, the domains of error event pairs and the information cost of IC faults included in the domains are derived. Finally, a tree-based minimal cost diagnosis algorithm is proposed to find the locations of the IC faults. Laboratory testbed is constructed and the case studies are conducted to demonstrate the performance of the proposed method. The results show that IC fault identified by the proposed method agree well with the case study setups.
Design of the Remote Monitoring and Fault Diagnosis System for Power Electronic Equipment

马皓,韩思亮

DOI: https://doi.org/10.3321/j.issn:1000-1026.2005.02.011

2005-01-01

Abstract:To meet the requirement of highly real-time, tremendous data transferring and complicated diagnostic causes of remote monitoring and fault diagnosis with power electronic equipment, a novel idea of distributed system with industrial PC (IPC) and PLC controlling field terminal is proposed in this paper. Based on the techniques of power electronics, fault diagnosis and network, a remote monitoring and fault diagnosis system with combination of a three-layer C/S structure and Internet is presented, which achieves with high compatibility between different equipment. Furthermore, the paper focuses on the discussion about the structure of compatible systems, the compatibility design of remote monitoring and the realization of field control equipment, such as the data collection sub-system, the real-time monitoring sub-system, the fault diagnosis sub-system and the data disposal and management sub-system, and the design of the data transferring sub-system and the communication protocol format.This work is supported by National Natural Science Foundation of China (No. 50207008).
Industrial Environment Temperature and Humidity Monitoring System Based on Wireless Sensor Network

Fang WEI,Zhao-xia ZHENG

DOI: https://doi.org/10.3969/j.issn.1002-1841.2018.05.014

2018-01-01

Abstract:In order to meet the production demand of modern industry , a temperature and humidity monitoring system based on wireless sensor network was designed .The system used MSP 430 as the development platform , the sensor data acquisition cir-cuit, the data processing transmission circuit , the minimum system circuit of the MCU and the upper computer monitoring plat-form were designed .Sensor network based on ZigBee protocol was responsible for the temperature and humidity data collection , with MSP430 microprocessor as the core of the gateway which was responsible for receiving and forwarding data , PC monitoring platform was used for real-time monitoring of temperature and humidity data collected.This system solves the problem of the tradi-tional temperature and humidity measurement , which is difficult to maintain and is not easy to maintain .It is suitable for the measurement of temperature and humidity in complex environment such as industrial production .
Research of measurement and control for bearing based on distributed system

钱少明,吴瑞明,徐志农,周晓军

DOI: https://doi.org/10.3969/j.issn.1001-2265.2004.02.032

2004-01-01

Abstract:The distributed automatic microbearing measuring system is introduced in this article, a three layers network is established by field-bus CAN and Ethernet based on TCP/IP protocol.The system consists of PC、IPC、PLC.This article also gives an account of the design of the multi -communition software.To irregular topology in distributed network,algorithm about communication path is discussed.
Design and Application of CAN/LIN Gateway Controller in Automotive Body Network

Wei Wei,Yao Wei,Zhang Wei

DOI: https://doi.org/10.3969/j.issn.1000-3886.2008.02.014

2008-01-01

Abstract:Utilizing the different characteristics of CAN and LIN bus protocol,a CAN/LIN gateway controller is built based on the main MCU of MC68HC08AZ60A.The communication of CAN/LIN is fulfilled,also with the implementation of car body network control.And for actual application,the design of low power and fauh-self-diagnosis is finished.
The design of electric motor car's body network based on CAN-bus distributed control

Wang Jianfeng,Wang Dafang,Xiong Jie

DOI: https://doi.org/10.1109/CCDC.2009.5191511

2009-01-01

Abstract:CAN-bus is a typical bus control technology, and is now widely applied in many areas.In view of the characteristics of the electric vehicle body, this paper puts forward a plan that applies CAN-bus technology to build electric vehicle body network. In terms of the electric vehicle body system, it needs to resolve several issues: One is to simplify electronic wiring harness as far as possible, and the other is to ensure the normal data communications. In this article, the body electrical is divided into different nodes in accordance with the principles of proximity, each node controls a certain area of electrical equipment, and at the same time, communicates with other nodes through CAN bus. CAN bus used SAE1939 agreement and defined message through this agreement. Each body node of the circuit includes main circuit board and extended board. The main circuit can achieve the requirements of data communications; the extended board can achieve the expansion of body electrical. The circuits are divided into several modules in application with circuit modular design approach. Every module was respectively developed by embedded software system through some software development tools, at the same time, tested the entire body CAN network communications systems. After the test, the entire body of communications network can meet the requirements.
Design of wind tunnel temperature and humidity data acquisition system based on CAN/SimpliciTI hybrid network

Haiyang Li

DOI: https://doi.org/10.1088/1742-6596/1176/6/062063

2019-03-01

Journal of Physics: Conference Series

Abstract:In order to obtain the temperature and humidity information of the Test section in the low-speed flue gas wind tunnel in real time, a low-power wind tunnel temperature and humidity data acquisition system based on CAN/SimpliciTI hybrid network is designed. The CAN network is used as the main network, while the SimpliciTI low-power wireless sensor network as the sub-network. The terminal ED nodes of sub-network acquire the ambient temperature and humidity information of the location and then transmit them to the gateway node by wireless mode. In the gateway node,the SimpliciTI messages are converted into CAN messages, and finally, they are delivered to the main network. The host computer communicates with the gateway node through the CANalyst-II protocol analyzer, and finally gets the temperature and humidity information of each ED terminal. Compared with the traditional bus type communication system, the system has the advantages of less wiring, simple network hardware, low power consumption, and convenient maintenance.
The Development of Embedded System Combining Inner CAN Bus and Outer Network Communication Protocol

YE Shu-ming,LI Ding-li

DOI: https://doi.org/10.3969/j.issn.1671-7147.2007.01.006

2007-01-01

Abstract:The design uses embedded system structure which communicates with external by using TCP/IP protocol and communicates with internal by using CAN bus.In this way,the flexibility and the reliability are improved effectively.The structure has been used to develop animalcule gross detect system,and tackes good effect.The result is fairly promising.
Design of Strength Test on Communication and Manipulation of CAN Nodes

WANG Jiang-bo,LI Wen-xin,MU De-jun,LEI Zhi-guang

DOI: https://doi.org/10.3969/j.issn.1673-629x.2011.06.050

2011-01-01

Abstract:Along with the development of bus technology,CAN bus,as one of typical field buses,has already been in widespread use.In order to fulfill the request of safety as well as reliability in stress test towards CAN nodes,a design is given in this paper whose key point is a real-time data transfer transponder with double channel CAN bus and USB 2.0 port.The receive and dispatch process of CAN data and real time data transfer process among host machines are implemented by a MCU of high performance to detect the management performance as well as design surplus in transferring data among CAN nodes under test.Continuous receive and dispatch process about CAN frames has been fulfilled by the transponder,and the frame gap can be controlled strictly in dozens of micro-seconds.Together with test software in host machine,strength and performance test about CAN bus can be done.Moreover,if analysis software of host machine is properly configurated,this transponder can be treated as protocol analysis instrument of CAN double bus,and power supply with USB port is quite convenient and portable as well.
Hierarchical distributed CAN Bus optical fibre network monitoring system

Yu Qingguang,Zhang Xiaoming

DOI: https://doi.org/10.3321/j.issn:0254-3087.2006.z3.269

2006-01-01

Abstract:In this paper, a hierarchical distributed CAN bus optical fibre network monitoring system was designed. The optical CAN bus system has been introduced, according to the system, real-time monitoring control and data acquisition for Cascade STATCOM has been carried out. It can accurately obtain operating conditions of the STATCOM system and provide comprehensive real-time monitoring. The designed system has been proved successful in a 50MVAR Cascade STATCOM, and also available for other FACTS/DFACTS devices.
On-line Monitoring Device in Substation Based on the Technology of CAN Bus and ARM Microprocessor

CAI Jun-yu,XU Guo-zheng,GUAN Yong-gang,HUANG Yu-long

DOI: https://doi.org/10.3969/j.issn.1001-1609.2006.06.006

2006-01-01

Abstract:A multi-layer distributed on-line monitoring system of substation is designed in this paper.The on-line monitoring IED(Intelligent Electronic Device) is placed in each bay to uninterruptedly monitor and control primary devices per bay.The IED is based on CAN filed-bus and ARM microcontroller.CAN filed-bus is introduced for internal communication and ethernet for external communication with substation computer.The presented device is excellent in the ability of real-timing,interoperability,anti-jamming and extensibility.
Application design of CAN bus in tractor test bench

wu feng,sun jun,feng an,yang zhijia,zhu jianxin

DOI: https://doi.org/10.3321/j.issn:1002-6819.2005.06.017

2005-01-01

Abstract:<Abstrcat> A data sample system based on CAN bus of tractor test bench was introduced in this paper. Some (problems) of traditional test bench were solved, such as complex in setting wire, low level of reliability, unfit for connection to net. This system consists of five CAN nodes, each of them can finish the correlative test and send the data to main PC. The main PC communicates with the CAN nodes through PC-CAN adapter. Hardware and software design for the CAN nodes and PC-CAN adapter and system debugging were finished in this project.
Satellite Onboard Tele-Command And Telemetry Control System Based On Control Area Network (Can)

Jp Xiong,B Li,Zy Cheng,N He,C Ma

2002-01-01

Abstract:A set of extended communication protocols are designed and built upon CAN link layer frame structure, which support command datagram switch and large block data exchange. The distributed TTC system structure details are given and two kinds of CAN hardware node design are also discussed. One kind of node with internal processor running stand alone plays the role of monitoring and creating telemetry packet under the control of received commands, another kind of node is peripheral to other computer processor and is in charge of data exchange under the master processor. Finally some performance testing results are given and analyzed, resulting in that the design and implementation of the TTC system meets the mission requirements.
Intelligent Control Network Design Based on CAN-bus for Audio Equipment

Xiuli Zhang,Zhong Wan,Deyang Yang,Weidong Chen

2011-01-01

Abstract:In order to solve the problem of inconvenience in network construction, short transmission distance of RS232 and non-intelligence audio device with different interface for network, this paper presented a design of the audio intelligent control network based on CAN(Controller Area Network)-Bus. The topology of audio control network, structured models of ICANNet and hardware are firstly discussed. Then the protocol of transport layer and application layer and software of intelligent control network is studied. Finally the test results were given to demonstrate the feasibility and reliability of the design.
A design of CAN-bus based collector for Automatic Meter Reading system

J. Jun,Zhang Fuan,Liangzhong Fan

DOI: https://doi.org/10.1109/CINC.2010.5643730

2010-11-22

Abstract:A design of CAN-bus based collector for AMR (Automatic Meter Reading) system is presented in this paper. The design uses the VRS51L3074 MCU as microprocessor control unit, reed switch as sensor, CAN-bus as data transmission line, three-terminal regulator as power. Experiments show that the collector is robust and can meet the actual requirements, and it has abroad application prospects in remote measure and management fields.

Computer Science,Engineering
The research of tunnel monitoring system based on CAN bus

Xu Qian,Sun Zhifeng

DOI: https://doi.org/10.3969/j.issn.0258-7998.2011.02.028

2011-01-01

Abstract:The research of tunnel monitoring system is based on CAN bus.The main function of the system,hardware structure and software design are discussed in detail.The regional control blocks use ARM Cortex-M3 as their control chip,and adopt embedded RTOS as their operating system.All these ensure the system's high reliability and real-time performance.
The Design of the Embedded Bus Controller Based on the Network Monitor System

JIANG Ying,WANG Pei-dong,YANG Xiang-dong

DOI: https://doi.org/10.3969/j.issn.1007-2683.2005.01.030

2005-01-01

Abstract:In order to solve the logic structure which is getting more and more complicated in the industry control system, based on the network monitor system, using the embedded Linux operation system, put forward a comparably complete resolve method of the design and implement based on the network bus controller. Using the RS-232 and CAN controller bus to communicate with the I/O node, and implementing the real-time monitor of the underlayer, the main console can directly connect into the Internet with the network function of the embedded system, passing the information of the system trouble to the main console, implementing the long -distance diagnosis. This system runs stably during the test and the network delay is less than 100ms, this system has the potential application value after being extended.
Design and Implementation of An On-board Measurement System based on CAN Bus

Wang Junhua,He Le,Zhao Yin,Xia Qunsheng

2009-01-01

Abstract:To solve the deficiency existing in the original on-board measurement system of a test vehicle,a new on-board measurement system is presented based on CAN bus.By analyzing the existing CAN bus application level protocol of the test vehicle,CAN bus application level protocol of a new on-board measurement system is obtained from test,and relevant interface circuit is implemented.The designed measurement system fully utilizes the existing CAN bus signal of the test vehicle and uses CANcardXL data acquisition card and CANoe software to realize in-phase data acquisition of the test vehicle and the exterior CAN bus.Validity of the new measurement system is proved by road test.

Minitype Electrical Network Monitoring System Based on CAN Communication

The Design and Realization of PLC Remote Monitoring and Diagnosing System

Multi-node data acquisition and analysis system for the development of AT electronic control unit.

Tree-Based Intermittent Connection Fault Diagnosis for Controller Area Network

Design of the Remote Monitoring and Fault Diagnosis System for Power Electronic Equipment

Industrial Environment Temperature and Humidity Monitoring System Based on Wireless Sensor Network

Research of measurement and control for bearing based on distributed system

Design and Application of CAN/LIN Gateway Controller in Automotive Body Network

The design of electric motor car's body network based on CAN-bus distributed control

Design of wind tunnel temperature and humidity data acquisition system based on CAN/SimpliciTI hybrid network

The Development of Embedded System Combining Inner CAN Bus and Outer Network Communication Protocol

Design of Strength Test on Communication and Manipulation of CAN Nodes

Hierarchical distributed CAN Bus optical fibre network monitoring system

On-line Monitoring Device in Substation Based on the Technology of CAN Bus and ARM Microprocessor

Application design of CAN bus in tractor test bench

Satellite Onboard Tele-Command And Telemetry Control System Based On Control Area Network (Can)

Intelligent Control Network Design Based on CAN-bus for Audio Equipment

A design of CAN-bus based collector for Automatic Meter Reading system

The research of tunnel monitoring system based on CAN bus

The Design of the Embedded Bus Controller Based on the Network Monitor System

Design and Implementation of An On-board Measurement System based on CAN Bus