Abstract:This study aims to examine the 50/50 polypropylene/polyamide 6 (iPP/PA6) system molded under confined flow conditions, both in its original state and after being modified by two different interfacial agents. This study provides two main insights. Firstly, it focuses on a polymer blend close to phase inversion. Secondly, it investigates the impact of using two different types of interfacial agents (derived from polymer waste) to enhance the compatibility between iPP and PA6. Dynamic Mechanical Analysis (DMA) has been employed to achieve these objectives. It is important to note that the investigation of the 50/50 iPP/PA6 system is a crucial focus predicted in previous studies, where a series of mechanical properties were evaluated using Box–Wilson design of experiments (DOEs) over the whole compositional range on the iPP/PA6 binary system. Thus, two interfacial modifiers, namely succinic anhydride (SA)-grafted atactic polypropylene with terminal, side, and bridge SA grafts (aPP-SASA) and succinyl-fluoresceine (SF) with bridge succinic anhydride grafting atactic polypropylene (aPP-SFSA), were employed. The authors obtained and characterized these agents. The quantity of these agents used in the blend was identified as a critical coordinate in prior studies conducted by the authors. The processing method used, compression molding under confined conditions, was chosen to minimize any orientation effect on the emerging morphology. All characterization procedures were performed on samples processed by contour machining to retain the blend morphologies as they emerged from the processing stage. Results from WAXS and SAXS synchrotron tests concluded there were no changes in the crystal morphology of the iPP or the PA6 in the blends nor any co-crystallization process throughout the compositional range. These findings, and the long period fits on the PP crystalline phase for the fifty/fifty blends we are discussing, will support the present DMA study. Finally, the efficiency of these interfacial modifiers has been concluded, even in this unfavorable scenario.

Dynamic Fracture Behaviors Of Polypropylene/Polyamide-6 Blends

Dynamic Fracture Properties of PP/PA6/POE-g-MA Studied by Caustics Method

Comparison Among Three Different Approaches to Dynamic Damage Measurement for Polymer Blends

Experimental Investigation of Dynamic Fracture Behaviors of Polymethyl Methacrylate

Morphologies, interfacial interaction and mechanical performance of super-tough nanostructured PK/PA6 blends

THE STUDY OF APPLIED BEHAVIOR OF PP/PA6 BY USING GRAFTED POLYPROPYLENE AS COMPATILIZER

Plastic damage mechanisms of polypropylene/polyamide 6/polyethelene-octene elastomer blends under cyclic tension

Dynamic Tensile Behavior of Polyamide 6 at Different Strain Rates: Experiments and Constitutive Model

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Microstructures and Mechanical Properties of Polypropylene/polyamide 6/Polyethelene-Octene Elastomer Blends

Deformation and fracture of polystyrene/polypropylene blends: A simulation study

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

Fracture Resistance Improvement of Polypropylene by Joint Action of Core–shell Particles and Nucleating Agent

Reactive Compatibilization and Elastomer Toughening of Poly(2,6-dimethyl-1,4-phenylene Oxide)/polyamide 6 Blends

Elastoplastic and fracture behaviour of semi-crystalline polymers under multiaxial stress states

Study on Dynamic Rheological Properties of PC/PA6 Blend

Impact Fracture Toughness of Short Glass Fiber-Reinforced Polyamide 6,6 Hybrid Composites Containing Elastomer Particles Using Essential Work of Fracture Concept

Dynamic Response and Fracture Characterization of Polymer-Clay Nanocomposites with Mode-I Crack

Study on the Structure and Properties of PA6/POE-g-MAH Blends

Toughening Behavior and Morphology Study of PA6/thermal Liquid Crystalline Polyamide Blends

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend