Abstract:Objective:To simulate the placement of percutaneous cortical bone trajectory (CBT) screws on reconstructed CT images and three-dimensional lumbar model and to measure the morphometric parameters for guiding the placement of percutaneous CBT screws.Methods:The CT images of 100 adult patients with lumbar spine diseases were studied. The CT images were reconstructed using Mimics software. Taking the projection point on the lamina at the junction of the inner and lower edge of the smallest coronal section of lumbar pedicle as the entry point, the cephalad angle, lateral angle, maximum screw length, maximum screw diameter, distance between trajectory and spinous process were measured. At the same time, the relationship between the trajectory and spinous process was observed by using the reconstructed three-dimensional image.Results:The lateral angle of the trajectory from L 1 to L 5 were 9.3° (8.9°, 9.8°), 9.6° (8.9°, 9.8°), 10.4° (9.5°, 11.3°), 11.81°±1.24° and 13.6° (12.5°, 14.5°), respectively. The cephalad angle from L 1 to L 5 were 26.6° (26.0°, 27.0°), 26.2° (25.7°, 26.5°), 26.9° (26.5°, 27.4°), 25.94°±0.92° and 24.3° (22.7°, 25.4°), respectively. Significant statistic differences were found among all levels in the cephalad angles and lateral angles. The mean diameters of the trajectory from L 1 to L 5 were 5.65±0.49 mm, 6.38±0.60 mm, 6.91±0.67 mm, 7.42±0.76 mm and 8.33 (7.59, 9.01) mm, respectively. Except L 1 and L 5, there were significant differences among all levels in the maximum screw diameters. The mean length of the trajectory from L 1 to L 5 were 36.4 (35.4, 37.0) mm, 36.7 (35.8, 37.3) mm, 37.6 (37.1, 38.1) mm, 37.8 (37.3, 38.1) mm and 36.2 (35.2, 36.9) mm, respectively, and there were also significant differences among all levels. The ration in superior endplate for each segment were 41.08% (34.36%, 45.60%), 37.94% (32.97%, 43.63%), 40.18% (34.56%, 44.49%), 38.61% (34.80%, 46.24%) and 40.9% (35.32%, 46.02%), respectively and statistical differences were significant between L 1 and L 2 and L 2 and L 5. The mean distance between the trajectory and the spinous process from L 1 to L 5 were 7.27±1.23 mm, 7.19 (5.97, 8.28) mm, 7.32 (6.01, 8.28) mm, 7.31±1.36 mm and 7.45 (6.32, 8.23) mm, respectively. In the sagittal CT image, the tip of the trajectory located near the posterior two-fifths of the superior end plate, and the extended line of the trajectory located at the inferior edge of spinous process. In the three-dimensional reconstruction model, no obstruction was found between the simulated screws and the spinous process. Conclusion:Lumbar CBT screw can be implanted percutaneously, and spinous process will not hinder the implantation process. Spinous process and upper endplate can be used as a sign to guide the percutaneous CBT screw implantation. Digital analog screw placement can offer a useful reference for the clinical application of percutaneous cortical bone trajectory screw.

The applied study of virtual-reality technology for accurate placement of C2 pedicle screws

Stepwise implantation of pedicle of upper-middle thoracic vertehral arch screws under guidance of C-shaped X-ray fluoroscopy:an experimental study

[Comparative Study Between 3D Guide Plate Assisted and Free-Hand Insertion of Anterior Cervical Transpedicular Screw].

Pedicle screw placement in the cervical vertebrae using augmented reality-head mounted displays: a cadaveric proof-of-concept study

Feasibility of mixed reality–based intraoperative three-dimensional image-guided navigation for atlanto-axial pedicle screw placement

Preoperative reformatting for C_2 pedicle screw track using three-dimensional computed tomography technique

Experimental study of cervical pedicle three-dimensional locator techniques

Deviation Analysis for C1/2 Pedicle Screw Placement Using a Three-Dimensional Printed Drilling Guide.

Accuracy of digital orthopedic three-dimensional reconstruction for thoracolumbar pedicle screw placement

The experimental study of lower cervical transpedicular screw placement with the assistance of individualized measurement of spiral CT scan

Fully automated determination of robotic pedicle screw accuracy and precision utilizing computer vision algorithms

Study on Pedicle Screw Fixation of Cervical Spine Assisted CT-based Navigation System Compared with the Individual Cervical Peddle Screws Placement Technique

Upper cervical pedicle screw implantation assisted by augmented reality in 3D-printed pediatric models: an experimental study

Design and Application of Individualized, 3-Dimensional-Printed Navigation Template for Placing Cortical Bone Trajectory Screws in Middle-Upper Thoracic Spine: Cadaver Research Study

The significance of CT multi-planar reconstruction of vertebral artery CT angiography in C2 pedicle screw placement

A Pilot Human Cadaveric Study on Accuracy of the Augmented Reality Surgical Navigation System for Thoracolumbar Pedicle Screw Insertion Using a New Intraoperative Rapid Registration Method

[Study of Pedicle Screw Placement Assisted by Intraoperative Three-Dimensional Navigation in Lumbar Vertebrae with Axial Rotation].

A novel method of cervical pedicle screw placement from C3 to C5 and its clinical applications.

Real-Time Navigation with Guide Template for Pedicle Screw Placement Using an Augmented Reality Head-Mounted Device: A Proof-of-Concept Study

Feasibility study of percutaneous placement of lumbar cortical bone trajectory screws based on CT data

Pedicle Screw Placement in the Thoracic Spine: a Randomized Comparison Study of Computer-Assisted Navigation and Conventional Techniques.