Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Severe Plastic Deformation Methods for Ultra-fine Grained Materials

Present State and Perspectives of Severe Plastic Deformation

Research and Development Prospects of Ultrafine-Grained Materials Fabricated by Severe Plastic Deformation

SPD Technology for Fabricating Bulk Nanocrystalline Materials

Grain Rotation In Plastic Deformation

New Insight for Mechanical Properties of Metals Processed by Severe Plastic Deformation

Experimental and numerical analyses of 45 steel during three dimensional severe plastic deformation (3D-SPD)

The Contribution of Severe Plastic Deformation to Research on Superplasticity

Influence of Grain Size and Texture on the Yield Strength of Mg Alloys Processed by Severe Plastic Deformation

Research progress of fabricating ultrafine-grained composites by severe plastic deformation

A novel method for preparing bulk ultrafine-grained material: Three dimensional severe plastic deformation

Atomistic modeling of idealized equal channel angular pressing process

On the Grain Size Dependent Working Hardening Behaviors of Severe Plastic Deformation Processed Metals

Nanostructures in Ti Processed by Severe Plastic Deformation

Severe Plastic Deformation for Al and Mg Matrix Composites with Particulate Reinforcements : A Survey

Fabrication of Nano/Ultra-Fine Grained IF Steel via SPD Processes: a Review

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

Manufacturing of fine-grained structures by multilevel kinking mechanism through a novel periodic undulating compression method: An example 7075 aluminum alloy

Research and Development Prospects of High Strength Mg Alloys Fabricated by Severe Plastic Deformation

Coupled Thermo-Mechanical Analysis of Severe Plastic Deformation for Producing Bulk Nanostructured Materials

Development of Advanced Technologies for the Production of Innovative Materials with a Submicrocrystalline Structure by Methods of Severe Plastic Deformation