Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Coupled Thermo-Mechanical Analysis of Severe Plastic Deformation for Producing Bulk Nanostructured Materials

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Micromechanical Simulation of Fracture Behavior of Nanostructured Metals with Bimodal Grain Size Distribution

Numerical Analysis of Nano- or Micro-Crystalline Materials During Ecap by Dislocation Evolution Method

FEM Simulation of Micro-Crystalline Materials During ECAP Based on the Dislocation Evolution Method

SPD Technology for Fabricating Bulk Nanocrystalline Materials

Atomistic modeling of idealized equal channel angular pressing process

MACRO- AND MICROSCOPIC APPROACHES TO PLANE STRAIN DEFORMATION STATES OF FACE-CENTERED CUBIC METALS UNDER WEDGE INDENTATION

On the Grain Size Dependent Working Hardening Behaviors of Severe Plastic Deformation Processed Metals

Finite Element Analysis for Multi-pass Equal Channel Angular Pressing

Microhardness Distribution and Microstructural Evolution in Pure Aluminum Subjected to Severe Plastic Deformation: Elliptical Cross-Sectioned Spiral Equal-Channel Extrusion (ECSEE)

New Insight for Mechanical Properties of Metals Processed by Severe Plastic Deformation

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

Electrical-thermal-mechanical coupled modeling and simulation on deformation behaviors of Ti6554 alloy in electrically-assisted micro-tension

Severe plastic deformation of commercially pure aluminum using novel equal channel angular expansion extrusion with spherical cavity

Finite Element Analysis of Repeated Forging Severe Plastic Deformation

Nanostructures in Ti Processed by Severe Plastic Deformation

Modelling of ultra-thin steel sheet in two-stage tensile deformation considering strain path change and grain size effect and application in multi-stage microforming

Rapid Finite Element Analysis of Bulk Metal Forming Process Based on Deformation Theory

Nanophase And Ultrafine-Grained Powders Prepared By Mechanical Milling: Full Density Processing And Unusual Mechanical Behavior