Abstract:Steels with sub-micrometre grain sizes usually possess high toughness and strength, which makes them promising for lightweighting technologies and energy-saving strategies. So far, the industrial fabrication of ultrafine-grained (UFG) alloys, which generally relies on the manipulation of diffusional phase transformation, has been limited to steels with austenite-to-ferrite transformation<a href="#ref-CR1">1</a>,<a href="#ref-CR2">2</a>,<a href="/articles/s41586-021-03246-3#ref-CR3">3</a>. Moreover, the limited work hardening and uniform elongation of these UFG steels<a href="/articles/s41586-021-03246-3#ref-CR1">1</a>,<a href="/articles/s41586-021-03246-3#ref-CR4">4</a>,<a href="/articles/s41586-021-03246-3#ref-CR5">5</a> hinder their widespread application. Here we report the facile mass production of UFG structures in a typical Fe–22Mn–0.6C twinning-induced plasticity steel by minor Cu alloying and manipulation of the recrystallization process through the intragranular nanoprecipitation (within 30 seconds) of a coherent disordered Cu-rich phase. The rapid and copious nanoprecipitation not only prevents the growth of the freshly recrystallized sub-micrometre grains but also enhances the thermal stability of the obtained UFG structure through the Zener pinning mechanism<a href="/articles/s41586-021-03246-3#ref-CR6">6</a>. Moreover, owing to their full coherency and disordered nature, the precipitates exhibit weak interactions with dislocations under loading. This approach enables the preparation of a fully recrystallized UFG structure with a grain size of 800 ± 400 nanometres without the introduction of detrimental lattice defects such as brittle particles and segregated boundaries. Compared with the steel to which no Cu was added, the yield strength of the UFG structure was doubled to around 710 megapascals, with a uniform ductility of 45 per cent and a tensile strength of around 2,000 megapascals. This grain-refinement concept should be extendable to other alloy systems, and the manufacturing processes can be readily applied to existing industrial production lines.

A novel method for preparing bulk ultrafine-grained material: Three dimensional severe plastic deformation

Experimental and numerical analyses of 45 steel during three dimensional severe plastic deformation (3D-SPD)

Facile route to bulk ultrafine-grain steels for high strength and ductility

An Ultrahigh Strength Steel with Ultrafine-Grained Microstructure Produced Through Superplastic Forming

Superplastic characteristic of Mn–Si–Cr alloyed ultrahigh carbon steel realized through a novel process

Ultrafine-grained Mg-Zn-Y-Zr alloy with remarkable improvement in superplasticity

A novel process to obtain ultrafine-grained low carbon steel with bimodal grain size distribution for potentially improving ductility

SPD Technology for Fabricating Bulk Nanocrystalline Materials

Superplastic Deformation Behavior of Fine-Grained AZ80 Magnesium Alloy Prepared by Friction Stir Processing

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

Ultra-fine-Grained Ferrite Prepared from Dynamic Reversal Austenite During Warm Deformation

Microstructures and mechanical deformation behaviors of ultrafine-grained commercial pure (grade 3) Ti processed by two-step severe plastic deformation

Manufacturing of fine-grained structures by multilevel kinking mechanism through a novel periodic undulating compression method: An example 7075 aluminum alloy

Granular Carbides-Assisted Ultrafine-Ferrite Fabrication in the Pearlitic Steel Without Severe Plastic Deformation and Annealing

Tailoring Pre-Deformation Microstructure – an Easy Way for Nanocrystallization

Research and Development Prospects of High Strength Mg Alloys Fabricated by Severe Plastic Deformation

Achieving superior strength and ductility synergy in bulk ultrafine grained Al-Mg-Sc-Zr alloy via powder pre-aging

Research and Development Prospects of Ultrafine-Grained Materials Fabricated by Severe Plastic Deformation

Achieving a Compatible Tensile Strength and Ductility of Bulk Ultrafine Grained Al by Spark Plasma Sintering Plus Annealing

Influence of severe plastic deformation on the precipitation hardening of a FeSiTi steel

Preparation of ultrafine-grained Nb-1Zr alloy by increasing the time of large plastic deformation during friction stir processing