Abstract:Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) was developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) were comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibited a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at −20 °C. In contrast, the HR-QT steel exhibited tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consisted of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reached 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared with the HR-QT process, the TMCP-DQP process resulted in a finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieved the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilized the RA through carbon enrichment, while the relaxation stage reduced a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminated internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

An Ultrahigh Strength Steel with Ultrafine-Grained Microstructure Produced Through Superplastic Forming

Superplastic characteristic of Mn–Si–Cr alloyed ultrahigh carbon steel realized through a novel process

The Fabrication of Ultrahigh-Strength Steel with a Nanolath Structure via Quenching-Partitioning-Tempering

Dynamic reverse phase transformation induced high-strain-rate superplasticity in low carbon low alloy steels with commercial potential

Microstructural and mechanical properties of ultra-high-strength dual-phase steel produced by ultra-fast cooling

Formation of hierarchically structured martensites in pure iron with ultrahigh strength and stiffness

Study on the Formation and Mechanical Stability of Retained Austenite in Complex Phase Steel with High Formability

Design of Tri-Phase Lamellar Architectures for Enhanced Ductility in Ultra-Strong Steel

Achieving 2.2 GPa Ultra-High Strength in Low-Alloy Steel Using a Direct Quenching and Partitioning Process

Facile route to bulk ultrafine-grain steels for high strength and ductility

Achieving 1.7 GPa Considerable Ductility High-Strength Low-Alloy Steel Using Hot-Rolling and Tempering Processes

A cryogenic ultra-strong and ductile steel induced by stable nanoscale dual-phase structure

Obtaining Excellent Mechanical Properties in an Ultrahigh-Strength Stainless Bearing Steel via Solution Treatment

A novel method for preparing bulk ultrafine-grained material: Three dimensional severe plastic deformation

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

Dual Nanoprecipitation and Nanoscale Chemical Heterogeneity in a Secondary Hardening Steel for Ultrahigh Strength and Large Uniform Elongation

Superhigh strength and ductile press-hardening steel produced by shortened austenitization of microstructure containing Mn/Cr-rich cementite particles

Strength-plasticity transition mechanism after the solution treatment of GH3230 superalloy fabricated via laser powder bed fusion

Ultrahigh strength in lightweight steel via avalanche multiplication of intermetallic phases and dislocation

Microstructure and high-temperature tensile behavior of spray-formed modified 2000MPa H13 hot work die steel with 0.5wt % carbon

Achieving Superior Ductility at High Strain Rate in a 1.5 GPa Ultrahigh-Strength Steel without Obvious Transformation-Induced Plasticity Effect