Abstract:Herein, the effect of recrystallization on the bainite transformation and mechanical properties of CH steel were investigated using SEM, TEM, EBSD, dilatometry, and tensile testing machine. First, precipitation was introduced to hinder recrystallization by batch annealing. Subsequently, the competitive relationship between austenite transformation and recrystallization was revealed using different annealing processes. Finally, the effect of recrystallization on bainite transformation was analyzed, mainly including bainite morphology, fraction, transformation rate, bainite nucleation rate of untransformed austenite and austenite-bainite orientation relationship, as well as the effect on the mechanical properties. After batch annealing, a large amount of cementite and nanoscale (Nb, Ti)C precipitated in the hot-rolled sheet, the austenite transformation start temperature (A c1) and the pearlite to austenite transformation end temperature (A c1f)of the cold-rolled sheet increased, and the austenite transformation end temperature (A c3) of the cold-rolled sheet decreased, and the austenite transformation process accelerated. The microstructure of annealed sheets is consisted of ferrite, granular bainite, martensite, and a small fraction of retained austenite. Carbide hindered the recrystallization process during the annealing process, resulting in significant refining of the grains. The lower degree of recrystallization promoted bainite transformation, providing more nucleation sites, higher grain boundary and autocatalytic nucleation activation energy, improving bainite's fraction and transformation rate. The bainitic ferrite was mainly lathy in the recrystallized zone and polygonal in the non-recrystallized zone. Both a K-S and an N-W relationship between retained austenite and bainite, while the N-W relationship in the non-recrystallized zone was relatively higher. Without severe loss of plasticity, hindering recrystallization increased the dislocation, grain refinement, and precipitation strengthening values of the samples, and the strength significantly improved. However, with the increase of annealing temperature, recrystallization fraction increased gradually, and the increase in strength became less noticeable.

Study on the Formation and Mechanical Stability of Retained Austenite in Complex Phase Steel with High Formability

Evolution of Microstructure, Properties, and Fracture Behavior with Annealing Temperature in Complex Phase Steel with High Formability

Mechanical properties and deformation mechanisms of a novel austenite-martensite dual phase steel

Characterization of Retained Austenite in Advanced High-Strength Steel.

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering

Cr-enriched carbide induced stabilization of austenite to improve the ductility of a 1.7 GPa−press-hardened steel

Microstructure, mechanical properties and strengthening mechanism of high strength hot-rolled ferrite-martensite dual phase steel

Tailoring Bainitic Transformation and Enhancing Mechanical Properties of Carbide-Free Bainitic Steel Via High-Temperature Ausforming

Microstructure Analysis and Quantitative Strengthening Evaluation of Medium Carbon Bainitic Multiphase Steel

Tailoring the metastable reversed austenite from metastable Mn-rich carbides

Effect of Rapid Tempering at High Temperature on Microstructure, Mechanical Properties and Stability of Retained Austenite of Medium Carbon Ultrafine Bainitic Steel

Stability of Retained Austenite and Work Hardening Behavior in Ultra-Fine Medium Carbon Bainitic Steel

The Influence of Microstructure and Process Design on the Plastic Stability of 4 wt% Medium‐Manganese Steels

Microstructure and Mechanical Properties of a Novel Cast Multi-Phase Stainless Steel

Mechanisms of strength–plasticity enhancement and stress-induced phase transition in a medium-carbon low-alloy steel

Effect of Retained Austenite on the Fracture Behavior of a Novel Press-Hardened Steel

Multiphase precipitation and its strengthening mechanism in a V-containing austenite-based low density steel

Effect of austenitic state before ferrite transformation on the mechanical behavior at an elevated temperature for seismic-resistant and fire-resistant constructional steel

Improving the Cryogenic Strength–Ductility–Toughness of Multi‐Alloy Steel by Optimizing the Feature of Retained Austenite

Tailoring the strength and impact toughness of 9Cr1.5Mo1Co steel by optimizing ultra-fine martensite and retained austensite

Effect of recrystallization on bainite transformation and mechanical properties of complex phase steel with high formability (CH steel)