Abstract:Air‐hardening forging steels are a new steel concept, promising high strength and ductility combinations in combination with a reduced environmental impact. Herein, the effect of the microstructure before intercritical annealing is discussed in regard to microstructure evolution and strain hardening behavior. It is demonstrated that the microstructure prior to intercritical annealing governs the microstructures and final mechanical properties. The influence of different microstructures on the plastic stability of an air‐hardened industrially produced medium‐manganese steel is presented. For this matter, heat treatment parameters before and during intercritical annealing (IA) are varied, to achieve different microstructures. The resulting duplex microstructure is consecutively tested by tensile tests, which are monitored by digital image correlation (DIC) to obtain information on the local plastic deformation. The tests are accompanied by microstructure investigations using optical, scanning electron, and transmission electron microscopy. Finally, X‐ray and electron backscatter diffraction experiments are performed before and after deformation, to describe the altering phase fractions. It is demonstrated that the effect of the deformation temperature prior to IA treatment has a significant influence on the duplex microstructure, as it changes the austenite morphology from lamellar to globular and increases the phase fraction. The change in austenite phase fraction and morphology results in a higher yield strength (≈100 MPa), as well as higher uniform and total elongations (+2% and +5%, respectively). The DIC and tensile tests reveal that these differences in the austenite phase lead to a complete change in the strain hardening behavior, from continuous flow to discontinuous serrated flow, with clearly visible deformation bands during plastic deformation.

Cr-enriched carbide induced stabilization of austenite to improve the ductility of a 1.7 GPa−press-hardened steel

Enhancement of strength-ductility trade-off in a 2000 MPa grade press-hardened steel via refined martensite with stable high-density cementite

Superhigh strength and ductile press-hardening steel produced by shortened austenitization of microstructure containing Mn/Cr-rich cementite particles

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering

Improving the ductility of ultrahigh strength lath martensite through heterogeneous carbon distribution

Study on the Formation and Mechanical Stability of Retained Austenite in Complex Phase Steel with High Formability

A Novel 1000 MPa Grade Ultrafine-Grained Dual-Phase Press Hardening Steel with Superior Oxidation Resistance and High Ductility

Improving the Cryogenic Strength–Ductility–Toughness of Multi‐Alloy Steel by Optimizing the Feature of Retained Austenite

Dual Nanoprecipitation and Nanoscale Chemical Heterogeneity in a Secondary Hardening Steel for Ultrahigh Strength and Large Uniform Elongation

Synergistic strengthening effect achieved good ductility in ultrahigh strength Fe-22Mn-8Al-0.8C austenitic lightweight steels

Tailoring the strength and impact toughness of 9Cr1.5Mo1Co steel by optimizing ultra-fine martensite and retained austensite

A novel medium-Mn steel with superior mechanical properties and marginal oxidization after press hardening

Promoting ductility and formability in a carbide free bainitic steel via pre-annealing treatment

Design of Reduced Activation Ferritic/Martensitic Steels by Multiphase Optimization During the Entire Processing

Improving Mechanical Properties of a Forged High-Manganese Alloy by Regulating Carbon Content and Carbide Precipitation

Effectively improving the hardness-strength-toughness of carburized bearing steel via nanoprecipitates and fine grain structure

Achieving ultrahigh strength by tuning the hierarchical structure of low-carbon martensitic steel

The Influence of Microstructure and Process Design on the Plastic Stability of 4 wt% Medium‐Manganese Steels

Optimizing strength & ductility combination of medium-carbon TRIP steel via multi-stage work hardening

The Significance of Retained Austenite in the High Strength and Plasticity of Medium Carbon Q&P Steel

Strengthening and Toughening Mechanisms in Martensitic Steel