Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Tip Size-Effect and Temperature-Effect on PMMA Film Friction by Using an Integrated MEMS Probe Array

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Tribological behavior of reciprocating motion between ferromagnetic films coated with polymethylmethacrylate films under magnetic field

Load Dependence and Scanning Size Effect on Friction of Polytert-butylacrylate Film

Dry tribological properties of textured PMMA composites by embedding microspheres with different thermal conductivities

J0610104 Evaluation of Interatomic Force on the Tip of Probe by Using Microwave Atomic Force Microscope

Variation of MEMS Thin Film Device Parameters under the Influence of Thermal Stresses

Investigation on microtribological behavior of thin films using friction force microscopy

T0301-2-5 Modifying the Structure of Microwave AFM Probe for Improving the Sensitivity in the Measurement of Electrical Properties

Tip in Situ Chemical Modification and Its Effects on Tribological Measurements

Influence of Substrate Temperature on the Molecular Structure of Pmma Films Deposited by Pulsed Laser Deposition

Micro/Nanotribological and Mechanical Studies of Tin Thin-Film for Mems Applications

Contact size effects on the friction and wear of amorphous carbon films

Precise Characterization of Thermal Conductivity and Interfacial Thermal Resistance of Individual Polymer Microparticle

Molecular dynamics study on friction of polymer material polyoxymethylene (POM)

Probing the wear characteristics of graphene on flexible polymer substrates using a heated atomic force microscopy tip

Nano-indentation and nano-scratching of pure nickel and NiTi shape memory alloy thin films: an atomic-scale simulation

Investigation of Effect of Temperature and Strain Rate on Mechanical Properties of Underfill Material by Use of Microtensile Specimens

Temperature effect on mechanical strength and frictional properties of polytetrafluoroethylene‐based core‐shell nanocomposites

Friction characteristics of polymers applicable to small-scale devices

Size Effects in Internal Friction of Nanocrystalline Aluminum Films