Abstract:Binary TiAl (Ti29.8Al and Ti33.3Al, weight percent, hereafter in wt.%) alloys with different SiC fibers contents were prepared by arc melting. Microstructure, phase transformation, mechanical properties and related mechanism were elaborately researched. For the microstructure of Ti29.8Al alloy, the matrix consisted of fully alpha(2)/gamma lamellar colonies, the grain morphology changed from columnar to equiaxed when the SiC content reached 0.9%. For Ti33.3Al alloy, the matrix consisted of alpha(2)/gamma lamellar colonies and gamma phases, the columnar grains changed to equiaxed grains when the SiC content was more than 0.3%, and the grain size decreased from 150.9 to 69.3 pm with increasing SiC content. Ti5Si3 phases formed at the grain boundaries of both SiC-containing binary alloys. Ti2AlC particles would appear in the lamellar colonies when the SiC content was more than 0.9% in Ti29.8Al alloy and 0.3% in Ti33.3A1 alloy, respectively. The formation of Ti5Si3 and Ti2AlC phases resulted from the reaction of SiC fibers and TiAl alloy. The solid solution of C element in alpha(2) phase is higher than that in gamma phase, Ti2AlC will be more easily formed in Ti33.3Al alloy due to less alpha(2) phases and more gamma phases comparing with Ti29.8Al alloy. Compressive testing results showed that the strength and the strain of SiC-containing Ti29.8Al alloy were almost unchanged until the SiC content was 0.9%, which were improved to 1383 MPa and 6.5%, respectively. A good combination of strength and ductility of SiC-containing Ti33.3Al alloy was obtained, the highest values of them were 2196 MPa and 27.5% when the SiC content was 0.5%. Improvement of mechanical properties is caused by the grain refinement, grain boundary strengthening of Ti5Si3 particles, load transfer strengthening of Ti2AlC particles and solid solution strengthening of C and Si atoms.

Continuous Si–C–O–Al Fiber Derived from Aluminum-Containing Polycarbosilane Precursor

Synthesis of Polytitanocarbosilane and Preparation of Si–C–Ti–B Fibers

Fabrication of SiC ultrafine fiber with low oxygen content by electrospinning, thermal curing and pyrolysis of cyano-polycarbosilane

Structure and properties of fine diameter continuous SiC ceramic fiber reinforced Al matrix composites

Additive manufacturing of high mechanical strength continuous Cf/SiC composites using a 3D extrusion technique and polycarbosilane‐coated carbon fibers

Elemental and structural evolution of polymer-derived SiC fibers fabricated via solution blend and iodine curing methods

Fabrication of Silicon Carbide (sic) Coatings from Pyrolysis of Polycarbosilane/Aluminum

SiAlC ceramics from a new polyaluminocarbosilane: Synthesis, structure and oxidation behaviors

Flexible and thermally stable SiC fiber mats derived from electrospun boron-doped polyaluminocarbosilane precursors

Fabrication of Sic Fibres from Yttrium-Containing Polycarbosilane

Processing Continuous Submicro/Nano SiC Fibers by Electrospinning

LIQUID POLYCARBOSILANE DERIVED AI-CONTAINING SiC CERAMIC PRECURSORS——POLYALUMINOCARBOSILANE

Single-source-precursor synthesis and characterization of SiAlC(O) ceramics from a hyperbranched polyaluminocarbosilane

High-temperature resistance and thermal insulation performance of continuous SiMOC ceramic fibers fabricated by the modified sol-gel method combined with dry spinning

Synthesis and characterization of sol-gel derived continuous spinning alumina based fibers with silica nano-powders

Effect of polycarbosilane content on microstructures and mechanical properties of short-carbon-fibre-reinforced SiC composites

Microstructure Evolution and Mechanical Properties of TiAl Binary Alloys Added with SiC Fibers

Amorphous silica particles reinforced nickel matrix composites fabricated by in-situ pyrolysis of polycarbosilane

Polycrystalline Nanograin Formation in Uniform-Sized Silicon Carbide Fibers Derived from Aluminum-Containing Polycarbosilane

Fabrication of continuous SiOC ceramic fibers by polyethylene oxide assisted sol-gel method

Enhanced Mechanical Behavior and Fabrication of Silicon Carbide Particles Covered by In-Situ Carbon Nanotube Reinforced 6061 Aluminum Matrix Composites