Abstract:The accumulation of moisture inside the envelope under high-humid climates can strongly affect the hygrothermal properties and can lead to moisture-related damage / moulds to the materials, especially in severe weather con-ditions. However, the optimal insulation thickness of the exterior envelope is typically determined by factors such as overall heat transfer performance, carbon dioxide production and economic cost. The effect of insulation thickness on the annual average moisture content (AAMC) of a self-insulated exterior envelope is often neglected and seldom considered in the optimization process. In this study, a coupled heat, air and moisture transfer (HAM) model was derived and validated. Theoretical indices for water vapour transfer were implemented, such as moisture storage coefficient and moisture inertia factor. A simplified model for liquid water penetration and evaporation was also implemented. A novel four-dimensional moisture-energy-environment-economic (M3E) method that incorporates moisture content analysis was proposed for insulation thickness optimization. A case study was conducted on a self-insulated aerated concrete wall in two climate zones: the hot summer and cold winter (HSCW) zone and the cold zone. The insulation thickness interval investigated were 0-50 mm for interior thermal insulation (ITI) and 0-60 mm for exterior thermal insulation (ETI). The results of the case study showed that the AAMC of the entire envelope varied up to 15.2% (HSCW zone) and 10.0% (cold zone) for different insulation thicknesses. In the HSCW zone, the lowest AAMC of the outer part of the envelope adjacent to the atmosphere was found at 30 mm (ITI) or 20 mm (ETI), indicating the presence of turning thicknesses; while in the cold zones, the lowest AAMC was found at 50 mm (ITI) or 10 mm (ETI) with no turning thickness. The proposed theoretical implementations accounted for changes of AAMC in different interior/exterior insulation thicknesses and were verified with the results of numerical calculation. The proposed theoretical indices revealed an opposite effect of water vapour transfer and liquid water transfer on the AAMC for different insulation thicknesses, which can explain the presence of turning thickness. Furthermore, the selected optimal insulation thicknesses from Pareto fronts were found around 25-29 mm for ITI and 36-38 mm for ETI in two climate zones. The results from the M3E method showed a reduction in moisture risks (up to 62.91%) and mould growth risks (up to 4.84%) in the case study, successfully meeting the acceptable range of moisture risk and mould growth risk. The findings of this paper can help generate a new understanding of moisture transfer, and the proposed M3E method can be applied in all cases to reduce the moisture/mould growth risks in the design stage.

Thermal Performance Study on Modular Evaporative Cooling Sandwich Wall on Mechanical Ventilation Condition

The Energy Saving Effect of Different Wall Insulation Configurations with the Intermittent and Compartmental Heating Method

Numerical Study on Wall Insulation Construction Affecting the Energy Consumption under the Intermittent and Loculose Energy Use

The Influence of Wall Structures to Air Conditioner Energy Consumption Based on the Characteristics of Intermittent and Loculose Energy Use

Numerical Study On Energy Consumption Characteristics For Wall Insulation Structure In Hot Summer And Cold Winter Zone

Anti-insulation Behavior for Exterior Wall External Insulation on Residential Buildings in Hot Summer and Cold Winter Zone

Influence on energy saving effects of internal and external wall insulations for different occupant behaviors

Hygrothermal Performance of a Self-Insulated Exterior Wall with Various Exterior/interior Insulation Thicknesses in Two Climate Zones in China: A Novel Moisture-Energy-environment-economic (M3E) Method in Insulation Thickness Optimization

Optimum Insulation Thickness of External Walls by Integrating Indoor Moisture Buffering Effect: a Case Study in the Hot-Summer-cold-winter Zone of China

Performance study of ventilated energy-productive wall: Experimental and numerical analysis

Numerical simulations on the thermal performance of ventilated walls with passive solar heating and latent heat storage in winter

Summer thermal and energy performances assessment of a modular hydronic thermal barrier wall for ultra-low energy buildings - A field experimental study

Thermal Performance and Optimizing of Composite Trombe Wall with Temperature-Controlled DC Fan in Winter

Experimental study on the performance of a novel RC-PCM-wall

Study on optimization of thermal property parameters of phase change wallboard and its application simulation in the building

Wall Insulation Effect on Building Energy Efficiency with the Intermittent and Compartmental Energy Consuming Method

Study on Thermal Performance Measurement and Construction of Passive Exterior Wall with Low Energy: Teaching and Laboratory Building of Shandong Jianzhu University

Performance analysis of a novel phase-change wall of wood structure coupled with sky-radiation cooling

Thermal performance of cavity masonry walls and thermal design investigation in Western China

Experimental and Numerical Performance Analysis of an Active Cooling Wall Module Equipped with Micro-encapsulated Phase Change Material

Numerical Analysis on the Cooling Performance of a Ventilated Trombe Wall Combined with Venetian Blinds in an Office Building