Abstract:In this study, combustion synthesis involving mechanical milling and subsequent sintering process was utilised to fabricate Cu/AlxCuy/Al2O3 in-situ composite through the aluminothermic reduction of CuO powders. First, CuO and Al powders were mixed, and ball milled for 30–150 min to facilitate self-propagating high-temperature synthesis (SHS). Then, mechanically activated Al-CuO powders were mixed with elemental Cu powders and experienced subsequent cold compaction and sintering processes. The reactions during synthesis were studied utilising differential thermal analysis (DTA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Densification and hardness of green and sintered bodies were also obtained. The results indicated that despite the negative free energy of the aluminothermic reaction, an initial activation energy supply is required, and mixed Al-CuO powders did not show significant progress in the combustion synthesis method. The aluminothermic reaction became probable whenever the activation energy was entirely provided by high-energy ball milling or by the sintering of ball-milled Al-CuO mixed powders. DTA results showed that the aluminothermic reaction temperature of Al-CuO decreased with milling times, whereas after 150 min of ball milling, the reaction was completed. XRD patterns revealed that the formation of Al2Cu and Al2O3 reinforcing phases resulted from CuO reduction with Al. Al4Cu9, Cu solid solution, and Al oxide phases were observed in sintered samples. The relative density of the samples was reduced compared to the green compacted parts due to the nature of the Cu-Al alloy and the occurrence of the swelling phenomenon. The hardness results indicated that in-situ formation of reinforcing phases in samples that experienced thermally assisted thermite reaction yielded superior hardness.

Self-propagation high-temperature synthesis and casting of Cu–MoSi2 composite

Mechanically activated self-propagating high-temperature synthesis of titanium silicide-molybdenum disilicide composite using constituent elements

Tailoring the Composition and Structure of Nb-, Si-, and B-Doped Mo-Based Composite Materials in the Self-Propagating High-Temperature Synthesis Metallurgy Process

Synthesis and analysis of high-purity MoSi2 powder

Synthesis of SiC/MoSi2 composite by mechanical alloying and reactive sintering

Effect of Sn and Si on the Synthesis of Ti<sub>3</sub>Al(Sn/Si)C<sub>2</sub> by Self-Propagating High-Temperature Sintering

ZrC/Cu composites in situ fabricated by self-propagating high-temperature synthesis in Cu-Zr-C system

Thermophysical, Thermochemical Behavior of Cu Coated Sic Composite Particles

Novel coassembly route to Cu-SiO2 MCM-41-like mesoporous materials.

Elevated temperature strengthening of synthesized in situ MoSi2-SiC composite

The study of pressureless-sintered Mo(Si,Al)(2)-SiC composite

Controllable syntheses of Mo5Si3 and Mo3Si by silicothermic reduction of MoS2 in the presence of lime

Preparation and properties of W-Mo-Cu composite using solution combustion synthesized W Mo solid solution nanopowder

Processing of molybdenum disilicide

Mechanical Activation-Assisted Solid-State Aluminothermic Reduction of CuO Powders for In-Situ Copper Matrix Composite Fabrication

The Microstructure and Mechanical Property of Mo(Si, Al)2-SiC Composite Prepared by Infiltrating Melt Aluminum

In situ fabrication of TiC particulates locally reinforced aluminum matrix composites by self-propagating reaction during casting

Mechanical Alloying and Thermodynamic Analysis of Mo-Si Binary

Effects of Alloying on the Microstructures and Mechanical Property of Nb-Mo-Si Based in Situ Composites

Microstructure evolution and growth mechanism of Si-MoSi2 composite coatings on TZM (Mo-0.5Ti-0.1Zr-0.02 C) alloy

Synthesis of Casting Composite Materials Based on Tungsten Carbides with Nickel Binding by the SHS Metallurgy Method