Abstract:In this paper, the effects of different rare earth elements (La, Ce, Sm and Er) on the microstructure and mechanical properties of Al-6.7Zn-2.6 Mg-2.0Cu-0.1Zr alloys have been investigated. The results show that the addition of rare earth elements, especially those with a higher atomic number (La < Ce < Sm < Er), could effectively reduce the alloy grain size. Rare earth elements form Al11La3, Al4Ce, Al10Cu7Sm2 and Al8Cu4Er phases in the alloy. After being rolled, the small rare earth phases could pin the grain boundaries, inhibit recrystallization, and refine the structure during solid solution treatment. Moreover, the rare earth atoms would provide more nucleation sites for the precipitation of the η' phase to make it smaller during the aging treatment. Therefore, the rare earth elements can significantly improve the mechanical properties of the alloy through grain refinement and precipitation strengthening. Because Er has a lower solid solubility in Al matrix than other elements, and can form Al3 (Er, Zr) phase, this phase can effectively inhibit recrystallization behavior. Therefore, among all the studied rare earth elements, Er has the strongest strengthening effect, which increases the tensile strength and yield strength of the alloy by 40Mpa and 29Mpa, respectively. The Sm-containing alloy acquire more fine recrystallized grains after solid solution, so that the elongation of the alloy is increased to 14.3%, and its plasticity is the best.

Research Progress of Effect of Rare Earth Elements on Microstructures of Al-Cu-Mg-Ag Alloys

Effect of Rare Earth Ce Addition on the Microstructure and Mechanical Properties of an Al–Cu–Mg–Ag Alloy

Effects of Rare Earth Additions on Compound Structure and As-Annealed Properties of Cu-12%Ag

Study on Phases Formation and Modification Ability of Rare Earth Elements La, Ce, Sm and Er in Al–Zn–Mg–Cu–Zr Alloy

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

The Effect of Grain Refinement and Precipitation Strengthening Induced by Sc or Er Alloying on the Mechanical Properties of Cast Al-Li-Cu-Mg Alloys at Elevated Temperatures

Effect of the rare earth element Ce on the microstructure, properties and thermal stability of Cu-5Fe alloy

Influence of mixed rare earth elements(Y and Ce) on the microstructure and corrosion behaviour of Mg-4Al-3Ca alloy

Effects of Mg, Ce and Cu Content on Microstructure of 2D70 Aluminum Alloy

Effect of Ce and Y on Microstructures and Properties of Al-11.0Zn-3.1Mg-1.22Cu-0.1Sr-0.2Zr-0.1Ti Alloy

Study of the microstructure and mechanical properties of Mg-rare earth alloys

Effect of Rare Earth Element Ce on Microstructure and Properties of Aluminum Rod for Electrical Purpose

Effect of Minor Er Additions on the Microstructures and Mechanical Properties of Cast Al-Cu-Mg-Ag Alloys

Effect of Y and Ce Micro-alloying on Microstructure and Hot Tearing of As-Cast Al–Cu–Mg Alloy

Effect of rare earth Ce on the microstructure and mechanical properties of cast Al–7Si alloys

Effects of rare earth elements on microstructure and tensile properties of Al-Si-Cu alloy at 250 °C

Effect of Rare Earth on Microstructure of Γ-Tial Intermetallics

Effect of Ce Content on the Microstructure and Mechanical Properties of Al-Cu-Li Alloy

Effect of Ce on Hot Tearing Sensitivity of As-Cast Al-Cu-Mg-Y Alloy

Study on the Strengthening Mechanism of Rare Earth Ce in Magnesium Alloys, Based on First-Principle Calculations and Electronegativity Theory

Microscopic mechanism of mechanical property improvement of the casted Al-7Si-0.4Mg-0.3Y alloy