Abstract:Blending type of ABS with different polybutadiene rubber (PB) and polyacrylonitrile (AN) contents in SAN phase is prepared at 240 degrees C to study the effects of PB and AN content on the structure and the properties of DB/ABS blends. Different kinds of productive ABS along with the blend-type ABS are used to compare the properties of PC/ABS and DB/ABS blends comprehensively. All blends are made by melt blending for 10 min with sheer rate of 30 r/min. The result shows that, in DB/Blend-type ABS (70/30) blends, PB content exhibits significant influence on the tensile properties. Samples with 6.3 wt% of PB always show the best performance both in yield strength and elongation at break when AN content is fixed at 18 wt%, 25 wt% and 30 wt%; while increasing AN content in the sample with the same PB content would result in better blends properties even not so obvious as PB content. Scanning electron microscopy gives exactly the same trend for phase morphology with PB and AN contents, revealing best uniform scale of dispersed phase (ABS) among 0.5 - 1.2 mu m at 6.3 wt% of PB. Thermal gravimetric analysis shows that all DB/ABS blends have good thermal stability, which is not obviously affected by PB content and AN content. Single peak of glass transition shows good compatibility in the DB/ABS blends. Excellent compatibility of DB with ABS in the sample is exhibited through dynamic mechanical analysis. The glasstransition temperature of DB/ABS blends are closed to that of DB, mildly affected by PB and AN content. Besides, both blending type ABS and different kinds of productive type ABS are used to compare the properties of DB/ABS blends and traditional bisphenol-A-type PC/ABS blends. Basic laws of tensile properties in DB/ABS remain the same as in PC/ABS blends using different types of ABS.

Preparation of PC MABS Alloys by Bulk and Their Properties

Research on high quality PC/ABS alloy

Abs/蒙脱土纳米复合材料的制备、结构及性能

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Effects of ABS-g-MAH on mechanical properties and compatibility of ABS/PC alloy

Preparation of Amine-Functionalized Compatilizer for PC/ABS Blends

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

Development of ABS/PBT Blend Alloys

Effect of polybutadiene grafted methyl methacrylate copolymer on the mechanical performance of PC/ABS composites

Morphological, Mechanical Properties, and Fracture Behavior of Bulk-Made Abs Resins Toughened by High-Cis Polybutadiene Rubber

Mechanical Properties of ABS and ABS/PBT Alloy with Different Rubber Contents

Control of the Particle Microstructure During the Synthesis of Bulk‐polymerized Transparent Methacrylate‐acrylonitrile‐butadiene‐styrene Resin

Effect of Rubber Types on Synthesis, Morphology, and Properties of ABS Resins

Pithecellobium Clypearia Benth Fiber/Recycled Acrylonitrile-Butadiene-Styrene (ABS) Composites Prepared in a Vane Extruder: Analysis of Mechanical Properties and Morphology

Properties of Polymethacrylic Acid (PMMA) Grafted Acrylonitrile-butadiene-styrene Terpolymer (ABS) and Its Application

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Recycled Polycarbonate/acrylonitrile–butadiene–styrene Reinforced and Toughened Through Chemical Compatibilization

Structure and Properties of Isosorbide type Polycarbonate/ABS Blend

Preparation of PC/ABS alloy with high gloss and halogen-free flame retardancy

Modification of acrylonitrile-butadiene-styrene terpolymer by graft copolymerization with maleic anhydride in the melt. II. Properties and phase behavior

Preparation, microstructure and properties of ABS resin with bimodal distribution of rubber particles