Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

Low Noise and Low DC Offset Zero IF WLAN Receiving Front-end Design

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

Design of a WLAN Mixer with Low Flicker Noise and High Linearity

A Low Voltage CMOS RF Front-End for IEEE 802.11b WLAN Transceiver

An Ultra-Low-power 5ghz Front End with Feedforward Body Bias LNA and Single to Double Balance Subharmonic Mixer Topology for Direct Conversion Receiver

An Optimized Receiver RF Front-End

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

A RF CMOS Zero-IF Receiver Front-end for GSM/EDGE

A 2.4ghz Low Noise High Linearity RF Front-End Design.

Design And Simulation Of Low Noise Amplifier For Radio Frequency Front End Of Wireless Communication

Eliminating the Impacts of Flicker Noise and DC Offset in Zero-IF Architecture Pulse Compression Radars

A+21.2 Dbm Out-Of-Band Iip3 0.2-3ghz Rf Front-End Using Impedance Translation Technique

0.6–3-Ghz Wideband Receiver RF Front-End with a Feedforward Noise and Distortion Cancellation Resistive-Feedback LNA

A Low Power Direct Conversion Receiver RF Front-End with High In-Band IIP2/IIP3 and Low 1/f Noise

A CMOS Self-Mixing-free Front-End for Direct Conversion Applications

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

An Ultra-Low-Voltage 2.4-GHz Flicker-Noise-Free RF Receiver Front End Based on Switched-Capacitor Hybrid TIA With 4.5-dB NF and 11.5-dBm OIP3