Abstract:A combined computational/experimental study is performed to investigate hypersonic low-density internal gas flows in a convergent-divergent nozzle over a wide range of Knudsen numbers. The numerical solutions are obtained using the direct simulation Monte Carlo (DSMC) method and the experimental measurement is conducted in the hypersonic low-density wind tunnel FengDong-19 (FD-19) at China Academy of Aerospace Aerodynamics. Rarefaction effects are found to play an important role in pressure disturbance propagation, flow separation (vortex formation), mass flow rate, velocity slip, and thermally nonequilibrium effect. Pressure disturbance propagates farther upstream with increasing free-stream Knudsen number Kn∞. Although there is no flow separation near the nozzle surface for Kn∞ = 0.1, the slip velocity is such anomalously small that it cannot suppress flow separation, thus, producing one small vortex for Kn∞ = 0.2, 0.5 and 1. Due to the presence of the continuous sheet of two-order Moffatt vortices, the skin friction coefficient does not change sign (positive to negative) in the small separated region. This indicates that the incipient and small separated flows with second-order vortices may not be discerned by examining the sign of the skin friction. As Kn∞ grows to 2, this small vortex disappears. However, with further increase in Kn∞, a large vortex nearly fills the compression section of the nozzle due to the backflow effect. As Kn∞ increases from continuum to free molecular regime, the dimensionless mass flow rate mfr/mfr∞ rises first to its maximum at Kn∞ ∼ 0.2 resulting from the weaker flow blockage effect. After the maximum point, mfr/mfr∞ dwindles first because of the stronger backflow effect and rises again to its free molecular limit, obtaining its minimum (the so-called Knudsen minimum) at Kn∞ ∼ 10. DSMC results and experimental data obtained from FD-19 wind tunnel are in good agreement, achieving a mutual validation between computation and experiment. This indicates that our experiment provides valuable data that can server as “benchmark” case to support computational code evaluation and validation.

Flow Simulation and Nozzle Contour Analysis on Free Molecule Flow Micro-Resistojet

Analysis of the Flow Characteristics of Diffuser/Nozzle Based on MEMS

Coupled Electrostatic-Structures-Fluidic Analysis of a Nozzle/Diffuser Diaphragm Micropump

Numerical Study of Heat Flux Reduction Mechanism of the Counterflowing Jet in Rarefied Flows

Flow and Heat Transfer Characteristics in a Microchannel with a Circular Synthetic Jet

Numerical Investigation on Local Non-equilibrium Flows Using a Diatomic Nonlinear Constitutive Model

Numerical Simulation and Experiments on Gas Flow in Micro-Nozzle

Rarefied Couette Flows Performance in Micro Fluid Machinery Based on Improved DSMC Method

Simulation of Flow and Heat Transfer in Micro Couette Flow

Numerical and Experimental Investigation of Rarefied Hypersonic Flow in a Nozzle

Size Effect on Gas Flow in Micro Nozzles

Flow structure and parameter evaluation of conical convergent–divergent nozzle supersonic jet flows

Numerical Analysis of the Micro-Couette Flow Using a Non-Newton–fourier Model with Enhanced Wall Boundary Conditions

Design and simulation of a micro thrust solenoid valve nozzle based on CFD&DOE optimization analysis

Design and analysis of the scramjet nozzle with contact discontinuity

Direct Simulation Monte Carlo Analysis on Thrust Vectoring of a Supersonic Micro Nozzle using Bypass Mass Injection

Numerical investigation of thermochemical non-equilibrium effects in Mach 10 scramjet nozzle

Kinetic Simulation of Nozzle Flow in a Micronewton-Class Cold Gas Thruster

FABRICATION AND GAS FLOW CHARACTERISTICS ANALYSIS OF MICRO DIFFUSER/NOZZLES

GAS FLOW CHARACTERISTICS IN MICRO-NOZZLE

Cold flow characteristics of a novel high-hydrogen Micromix model burner based on multiple confluent turbulent round jets