Abstract:The magnitudes and distributions of the pressures around a tunnel lining are the most significant variables in shield tunnel design, as they determine the safety of the lining structure and influence the investment cost of the tunnel project. The grouting process has a negligible effect on the pressures exerted on the shield tunnel segmental linings when the boring machine is drilling. However, improper grouting control might result in large bending moments, local damage of segments and leakage at joints, leading to a reduction of the linings' safety, durability and serviceability. On the other hand, more and more special-section shield tunnels are developed to solve the problems associated with infrastructure construction under complex environmental conditions. How-ever, previous studies on the pressure distribution around tunnel linings all focused on circular tunnels. Few research about the loads during construction on special-section shield tunnels was conducted. In this study, three in-situ monitoring tests for the total pressure distributions of shallow buried quasi-rectangular tunnels in soft soils were carried out, which is deemed to be the first field study for special-section shield tunnels. Different grouting situations were adopted and the temporal and spatial distributions of the lining pressures during and after the construction were obtained. When the lining segments are pushed out of the shield tail, the adverse pressure distributions caused by grout ejections were observed which are typical non-uniform and unsymmet-rical. The effect of different grouting situations attenuates quickly in the longitudinal direction within a range of 9 rings. Additionally, the influence of the following back-up equipment and transportation carriages on the pressures outside the linings were first observed and studied by means of these field tests. The outside pressures fluctuated in different stages with the coincident pace of construction activities and performed as a counterforce and to resist the inside loads, which was different from the active loads exerted on the lining when the segmental rings were pushed out. From the long-term perspective, the pressure distributions in different tests tend to stabilize at a similar state. The influence of the grouting process or other construction loads on the lining pressures needed about 50 days to be relieved. A comparison between the measured results and the theoretical long-term pressures was conducted and the applicability of the proposed load distributions in the design model for quasi-rectangular tunnels was demonstrated. Additionally, a pressure mode combining cosinusoidal pressures and theoretical long-term pressures is proposed to predict the grouting pressures when lining segments are pushed out of the shield.

Research on DOT Shield Tunnel Back-filled Synchronous Grouting Diffusion and Segments Circumferential Pressure Distribution

Influences of grouting heave on overlying structures in shield tunneling

Study on Model of Back-Filled Grouting of Shield Tunnel

Two stage compound diffusion mechanism and pressure space-time distribution mode of synchronous grouting for large cross-section special-shaped shield

Numerical Investigation of Grout Diffusion Accounting for the Dynamic Pressure Boundary Condition and Spatiotemporal Variation in Slurry Viscosity

A semi‐elliptical surface compound diffusion model for synchronous grouting filling stage in specially shaped shield tunnelling

Study on Mechanism of Simultaneous Backfilling Grouting for Shield Tunneling in Soft Soils

Displacement infiltration diffusion model of power-law grout as backfill grouting of a shield tunnel

Research on Three-Dimensional Soil Deformation Induced by Double-O-Tube Shield Tunneling

Study on the Floating of Large Diameter Underwater Shield Tunnel Caused by Synchronous Grouting

Multiphase flow coupling analysis of shield synchronous grouting filling law with time-dependent viscosity

Study on the Grout Pressure Dissipation Mode in Simultaneous Backfill Grouting During Shield Tunneling

Investigation of the Pressure Distributions Around Quasi-Rectangular Shield Tunnels in Soft Soils with a Shallow Overburden: A Field Study

Spatial distribution model of the filling and diffusion pressure of synchronous grouting in a quasi-rectangular shield and its experimental verification

Model study on backfill grouting in shield tunnels based on fractal theory

Backfill grouting diffusion law of shield tunnel considering porous media with nonuniform porosity

Grout Diffusion in Silty Fine Sand Stratum with High Groundwater Level for Tunnel Construction

Study on the Influence of Back-fill Grouting Parameters in Unsaturated Strata on the Seismic Performance of Shield Tunnels

A study on grout consolidation and dissipation mechanism during shield backfilled grouting with considering time effect

Research on Dissipation of Excess Pore Water Pressure Caused by Shield Tunnelling

Research on Distribution of Initial Excess Pore Water Pressure Due to Shield Tunnelling