Abstract:Hollow glass microsphere (HGM) filled low-density polyethylene (LDPE) composites were prepared, and the effects of density, content, and surface modification of HGM on the thermal and dielectric properties of the composites were investigated. It is found that the thermal conductivity of the composites decreases with increasing HGM content or decreasing HGM density. At the same HGM content and density, the composites filled with suitable amount of silane coupling agent (KH570) modified HGM exhibit higher thermal conductivity than unmodified-HGM filled composites. The dielectric constant at 1MHz of the composites also decreases with increasing HGM content or decreasing HGM density, but their dielectric loss increases with increasing HGM content or increasing HGM density. By modifying the surface of HGM with suitable amount of KH570, the dielectric constant and loss at 1MHz of the composites can be decreased at the same time. The results of microwave dielectric properties of the composites indicate that the dielectric constant decreases with increasing HGM content or decreasing HGM density, the quality factor (Q×f) decreases with increasing HGM content or increasing HGM density, but both dielectric constant and quality factor are slightly affected by the surface modification of HGM. Due to lower intrinsic thermal conductivity and dielectric constant but higher dielectric loss of HGM than LDPE, the thermal conductivity and dielectric properties of the composites can be controlled with adding HGM and varying its volume fraction. The surface modification of HGM improves the interface contact between HGM and LDPE in the composites, which is confirmed by the SEM observation, and thus the heat conduction and dielectric properties at low frequency are improved. Based on calculated thermal conductivity and dielectric constant of HGM, the experimental trends of thermal conductivity and dielectric constant at 1MHz of the composites are analyzed by using different models, including typical models for particles-filled composites and special models developed for hollow microsphere filled composites. The results from suitable models show close correlation with the experimental values.

Mechanical, Thermal, and Flow Properties of HDPE-Mica Composites

Study on flow properties of HDPE/mica composites

Mechanical Properties of HDPE/Mica Composites

Effects of Matrix Molecular Weight on Structure and Reinforcement of High Density Polyethylene/Mica Composites

Melt flow properties and melt density of POM/EVA/HDPE nanocomposites

The effect of shear on mechanical properties and orientation of HDPE/mica composites obtained via dynamic packing injection molding (DPIM)

Synthesis, Characterisation and Enhanced Properties of Polyimide/mica Hybrid Films

Rheological Behavior for Mica-Filled Polypropylene Composite Melts

Effect of HDPE-g-MAH on Properties of HDPE/Graphite Thermal Conductive Composites

Thermal Conductivity and Mechanical Properties of High Density Polyethylene Composites Filled with Silicon Carbide Whiskers Modified by Cross-Linked Poly（vinyl Alcohol）

Tensile, Flow, and Thermal Properties of Caco3-Filled Ldpe/Lldpe Composites

Mechanical and rheological properties of HDPE/graphite composite with enhanced thermal conductivity

Grafted Polyolefin-Coated Synthetic Mica-Filled Polypropylene-Co-Ethylene Composites: A Study on the Interfacial Morphology and Properties

Investigation of thermal, rheological and mechanical properties of interfacially modified PP/mica composites

Melt flow properties and morphology of polypropylene composites filled with microencapsulated red phosphorus

Thermal, Electrical and Rheological Behavior of High-Density Polyethylene/graphite Composites

Study on fluidity and mechanics performance of UHMWPE/HDPE composite material

The Melt Flow Properties of Poly (propylene)/glass Bead Composites

A STUDY ON MECHANICAL PROPERTIES OF Γ-Ray IRRADIATION HDPE/MUSCOVITE

Processing and Properties of Mwnt/Hdpe Composites

Tailoring of Thermal and Dielectric Properties of LDPE-matrix Composites by the Volume Fraction, Density, and Surface Modification of Hollow Glass Microsphere Filler