Abstract:For the purpose of improving the thermal conductivity of the form-stable phase change materials (FSPCM), two types of nano-powders with high thermal conductivity were added into the samples. In the modified FSPCM, myristic acid (MA) was used as a solid-liquid phase change material (PCM), high density polyethylene (HDPE) acted as supporting material to prevent the leakage of the melted MA. Nano-Al2O3 (NAO) and nano-graphite (NG) were the additives for thermal conductivity enhancement. Scanning electronic microscope (SEM), Fourier transformation infrared spectroscope (FT-IR) and X-ray diffractometer (XRD) were used to analyze the microstructure, chemical structure and crystalline phase of the samples, respectively. Furthermore, the specific latent heat and phase transition temperature, thermal conductivity and thermal reliability were investigated using differential scanning calorimeter (DSC), thermal conductivity meter and thermo-gravimetric analyzer (TGA). The results showed that the MA was uniformly absorbed in the HDPE matrices and there was no leakage during the melting process when the mass fraction of the MA in the MA/HDPE composite was less than 70%. The DSC results revealed that the modified FSPCM have a constant phase change temperature and high specific latent heat. The thermal conductivity of the FSPCM was measured in the solid (30 degrees C) and liquid (60 degrees C) states of the MA. When the mass fraction of nano-powder additives is 12%, the thermal conductivities of the FSPCM increase by 95% (NAO) and 121% (NG) at 30 degrees C. It is anticipated that the FSPCM possess a potential application for thermal energy storage. (C) 2016 Elsevier Ltd. All rights reserved:

Study on flow properties of HDPE/mica composites

Effects of different treatments on the interface and mechanical properties of high density polyethylene reinforced by sericite-tridymite-cristobalite

Heat transfer during melting of graphene-based composite phase change materials heated from below

Rheological Behavior for Mica-Filled Polypropylene Composite Melts

Thermal Conductivity and Mechanical Properties of High Density Polyethylene Composites Filled with Silicon Carbide Whiskers Modified by Cross-Linked Poly（vinyl Alcohol）

PE/PE‐g‐MAH/Org‐MMT Nanocomposites. II. Nonisothermal Crystallization Kinetics

Thermally Stimulated Depolarization Currents and Dielectric Properties of Mg0.95Ca0.05TiO3 Filled HDPE Composites

Investigation of the Electrical Conductivity of HDPE Composites Filled with Bundle-Like MWNTs

Effect of HDPE-g-MAH on Properties of HDPE/Graphite Thermal Conductive Composites

Study on fluidity and mechanics performance of UHMWPE/HDPE composite material

Dielectric response of Mg 0.95 Ca 0.05 TiO 3 ceramic filled HDPE composites with low dielectric loss

Thermal conductivity of high density polyethylene filled with graphite

Investigation of thermal, rheological and mechanical properties of interfacially modified PP/mica composites

Synthesis and Thermal Properties of the Ma/Hdpe Composites with Nano-Additives As Form-Stable Pcm with Improved Thermal Conductivity

Effect of the melt flow index of compatibilizer on the melt processing and properties of highly filled magnesium hydroxide/linear low density polyethylene composites

STUDY ON PROPERTIES OF HIGH DENSITY POLYETHYLENE/WOOD FLOUR COMPOSITES

Study of the mechanical properties of mica-filled polypropylene-based GMT composite

Dynamic Rheological Properties for HDPE/CB Composite Melts

Study The Percolation Phenomenon Of High Field Volt-Ampere Characteristic In The Composite Of Low-Density Polyethylene/Nano-Siox

Investigation on Preparation and Properties of Mpe/pe-Ld/cb Electric Composites

Influence of Melting Viscosity on the Conductivity of CB/PP/HDPE Composites