Abstract:With the advantages of high mechanical strength and good electrical conductivity,Ni micronee-dle arrays are widely used in bioengineering and other fields.By virtue of the advantages of high replication accuracy and wide adaptability,the microelectroforming technique has become a reliable method for prepar-ing Ni microneedles.However,it is usually necessary to use photoresist template with the same thickness as that of the casting layer in the microelectroforming technique.Thick photoresist microelectroforming faces problems such as residual photoresist at the microstructure,difficulty in removing the photoresist.In order to solve the above problems,obtain Ni microneedle arrays with tip curvature radius on the nanome-ter scale,the fabrication process for Ni microneedle arrays based on the thin photoresist microelectroform-ing technique was designed and experimentally verified.First,a silicon template with arrays of pits was fabricated on(100)single crystal silicon wafers.Next,a Ni seed layer with a thickness of 200 nm was sputtered onto the surface of the silicon template.Then,a thin photoresist template of the microneedle support beam was prepared using the photolithography technique.Finally,Ni microneedle arrays were re-leased after microelectroforming.The experimental results show that Ni microneedle arrays with an aver-age deviation in size of 1.7 μm,an average deviation in absolute position of 1.8 μm,and an average curva-ture radius of 150 nm at the tip were obtained by this method without damaging the silicon template.Using RFJ-60 negative photoresist as a template for microelectroforming with a thickness of-2 μm,microneedle support beams with a thickness of-24.3 μm were successfully prepared.Ni microneedle relative dimen-sional error was reduced to 1%by compensating SiO2 lateral erosion into lithographic mask.Combining the microelectroforming technique and the anisotropic etching property of monocrystalline silicon,the Ni microneedle array can be prepared with high quality and high efficiency,which lays the foundation for the batch preparation of Ni microneedle arrays.

Design and Fabrication of Micro Needles Array Based on UV-LIGA Technology

Fabrication of Metal Micro Needle Array by LIGA Process

A New Low-Cost Fabrication Method for Micro Electro Mechanical System Microneedles

Hollow metallic microneedles fabricated by combining bulk silicon micromachining and UV–LIGA technology

Fabrication of taper hollow metallic microneedle array for portable drug delivery system

Study on Novel MEMS Hollow Microneedle Array

Fabrication of a polymer micro needle array by mask-dragging X-ray lithography and alignment X-ray lithography

Silica Needle Template Fabrication of Metal Hollow Microneedle Arrays

Patterned Microstructure Array Fabrication By Using A Novel Standing Surface Acoustic Wave Device

Fabricating process of hollow out-of-plane Ni microneedle arrays and properties of the integrated microfluidic device

Dense Vertical Su-8 Microneedles Drawn from A Heated Mold with Precisely Controlled Volume

Rapid Fabrication of Customizable Microneedle Molds Using Digital Light Processing 3D Printing Methods

Fabrication of SU-8 Microneedle Based on Backside Exposure Technology

A novel scalable fabrication process for the production of dissolving microneedle arrays

Rapid Fabrication of Microneedles using Magnetorheological Drawing Lithography.

Fabrication of micro-needle arrays using E-glass fibers by chemical etching

Design, Development, and Testing of Polymeric Microblades: A Novel Design of Microneedles for Biomedical Applications

Fabrication of densely arrayed micro-needles with flow channels by mechanical dicing and anisotropic wet etching

Research of Fabricating Transdermal Drug Delivery Solid Silicon Microneedles Based on Dicing and Wet Etch

Preparation of Ni Microneedle Array Using Thin Photoresist Microelectroforming Technique

Microneedle fabrication using the plane pattern to cross-section transfer method